DTC P0134 Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0134 | Heated Oxygen (HO2) sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions (a), (b), (c), (d) and (e) continue for more than 50 seconds (1 trip detection logic):
|
|

| Case | Heated Oxygen Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0134) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0134 | A |
| P0134 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1S1 and Engine Speed.
Warm up the engine until the engine coolant temperature reaches more than 40°C (104°F).
Rev the engine up to 4,000 rpm 3 times using the accelerator pedal.
Read the output voltage of the front Heated Oxygen (HO2) sensor displayed on the tester when the engine speed is suddenly increased.
|
| ||||
| NG | |
| 3.CHECK PCV HOSE CONNECTIONS |
|
| ||||
| OK | |
| 4.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C36 HO2 sensor (sensor 1) connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT1A (1) - +B (2) | 5.3 to 7.5 Ω at 20 °C (68°F) |
| HT1A (1) - E2 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 5.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI fuse.
Remove the EFI fuse from the integration relay.
Check the EFI fuse resistance.
Reinstall the EFI fuse.
Inspect the EFI relay.
Check the EFI relay resistance.
| Tester Connections | Specified Conditions |
| 1C-1 - 1A-4 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1A-2 and 1A-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() ![]() |
Disconnect the C36 HO2 sensor (sensor 1) connector.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| OX1A (C36-3) - OX1A (C20-112) | Below 1 Ω |
| HT1A (C36-1) - HT1A (C20-109) |
| Tester Connections | Specified Conditions |
| OX1A (C36-3) or OX1A (C20-112) - Body ground | 10 kΩ or higher |
| HT1A (C36-1) or HT1A (C20-109) - Body ground |
Reconnect the HO2 sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 7.CHECK WHETHER MISFIRE OCCURS BY MONITORING DTC AND DATA LIST |
|
| ||||
| OK | |
| 8.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leaks.
|
| ||||
| OK | |
| 9.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).
|
| ||||
| OK | |
| 11.CHECK FOR EXHAUST GAS LEAK |
|
| ||||
| OK | ||
| ||
| 12.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0134) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| No output | A |
| P0134 | B |
|
| ||||
| A | |
| 14.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
If the vehicle has run out of fuel, proceed to A.
If the vehicle has not run out of fuel, proceed to B.
|
| ||||
| A | ||
| ||