Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1607/84    Lost Communication with Front Satellite Sensor Bus LH

DTC    B1608/84    Front Satellite Sensor Bus LH Initialization Incomplete

DTC    B1617/84    Lost Communication with Front Airbag Sensor LH

DTC    B1618/84    Front Airbag Sensor LH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1607/84, B1608/84, B1617/84 or B1618/84 is recorded when a malfunction is detected in the front airbag sensor LH circuit.

DTC Code
Detection Condition
Trouble Area
B1607/84
B1608/84
B1617/84
B1618/84
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM


C162318E14


INSPECTION PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side and front airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

C158833E06

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A12-2 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    A12-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (+SL) - A12-1 (-SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (+SL) - A12-1 (-SL)
    Always
    1 MΩ or higher
    A12-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    A12-1 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 5
OK


4.CHECK FRONT AIRBAG SENSOR LH
C158831E08
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1607, B1608, B1617 or B1618 is output
    A
    DTC B1602, B1603, B1612 or B1613 is output
    B
    DTC B1602, B1603, B1607, B1608, B1612, B1613, B1617 and B1618 are not output
    C

    HINT:
    Codes other than DTC B1602, B1603, B1607, B1608, B1612, B1613, B1617 and B1618 or 83 and 84 may be output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B
REPLACE FRONT AIRBAG SENSOR LH
C

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)

C172830E03

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AD1-3 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    AD1-4 (-SL) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AD1-3 (+SL) - AD1-4 (-SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AD1-3 (+SL) - AD1-4 (-SL)
    Always
    1 MΩ or higher
    AD1-3 (+SL) - Body ground
    Always
    1 MΩ or higher
    AD1-4 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE