Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1642/81    Lost Communication with Driver Side Satellite Sensor Bus

for Preparation Click here


DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, side airbag sensor LH or RH, and rear airbag sensor LH or RH.
The side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1642/81 is recorded when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH).

DTC Code
Detection Condition
Trouble Area
B1642/81
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH) for 2 seconds.
  2. Driver side - side airbag sensor malfunction
  3. Driver side rear airbag sensor malfunction
  4. Center airbag sensor malfunction
  1. Floor wire
  2. Side airbag sensor LH (Driver side - side airbag sensor) (LHD)
  3. Side airbag sensor RH (Driver side - side airbag sensor) (RHD)
  4. Rear airbag sensor LH (Driver side rear airbag sensor) (LHD)
  5. Rear airbag sensor RH (Driver side rear airbag sensor) (RHD)
  6. Center airbag sensor assembly

WIRING DIAGRAM


C148422E28


C148422E29


INSPECTION PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and driver side - side airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and driver side - side airbag sensor.

  1. Check that the connectors (on the center airbag sensor assembly side and driver side - side airbag sensor side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR)

C158840E14

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    J17-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    J17-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    J16-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    J16-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    J17-4 (BBL+) - J17-3 (BBL-)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J16-4 (BBR+) - J16-3 (BBR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    J17-4 (BBL+) - J17-3 (BBL-)
    Always
    1 MΩ or higher
    J17-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    J17-3 (BBL-) - Body ground
    Always
    1 MΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J16-4 (BBR+) - J16-3 (BBR-)
    Always
    1 MΩ or higher
    J16-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    J16-3 (BBR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


4.CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the driver side rear airbag sensor.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


5.CHECK CONNECTORS
  1. Disconnect the connectors from the driver side - side airbag sensor and driver side rear airbag sensor.

  1. Check that the connector (on the driver side rear airbag sensor side) is not damaged.

    OK:
    The connector is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR - REAR AIRBAG SENSOR)

C148440E21

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    J17-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    J17-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    J16-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    J16-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 and 1 of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    J17-1 (BCL+) - J17-2 (BCL-)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J16-1 (BCR+) - J16-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    J17-1 (BCL+) - J17-2 (BCL-)
    Always
    1 MΩ or higher
    J17-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    J17-2 (BCL-) - Body ground
    Always
    1 MΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J16-1 (BCR+) - J16-2 (BCR-)
    Always
    1 MΩ or higher
    J16-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    J16-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


7.CHECK DRIVER SIDE - SIDE AIRBAG SENSOR
C158834E08
  1. Interchange the front passenger side - side airbag sensor with driver side - side airbag sensor and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 90 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1647 is output
    A
    DTC B1642 and B1647 are not output
    B
    DTC B1642 is output
    C



A
REPLACE DRIVER SIDE - SIDE AIRBAG SENSOR

B
USE SIMULATION METHOD TO CHECK (Click here)
C


8.CHECK DRIVER SIDE REAR AIRBAG SENSOR
C148441E11
  1. Interchange the front passenger side rear airbag sensor with driver side rear airbag sensor and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 90 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1642 is output
    A
    DTC B1647 is output
    B
    DTC B1642 and B1647 are not output
    C

    HINT:
    Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B
REPLACE DRIVER SIDE REAR AIRBAG SENSOR
C

USE SIMULATION METHOD TO CHECK (Click here)