DTC B1632/81 Lost Communication with Driver Side Rear Airbag Sensor |
DTC B1633/81 Driver Side Rear Airbag Sensor Initialization Incomplete |
| DTC Code | Detection Condition | Trouble Area |
| B1632/81 B1633/81 | When one of following conditions is met:
|
|


| 1.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the driver side - side airbag sensor and driver side rear airbag sensor.
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Disconnect the connectors from the driver side - side airbag sensor and driver side rear airbag sensor.
Check that the connectors (on the driver side - side airbag sensor side and driver side rear airbag sensor side) are not damaged.
|
| ||||
| OK | |
| 3.CHECK DRIVER SIDE - SIDE AIRBAG SENSOR |
![]() |
Interchange the front passenger side - side airbag sensor with driver side - side airbag sensor and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1632, B1633, B1637 and B1638 are not output | A |
| DTC B1637 or B1638 is output | B |
| DTC B1632 or B1633 is output | C |
|
| ||||
|
| ||||
| C | |
| 4.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR - REAR AIRBAG SENSOR) |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified condition |
| J17-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| J17-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
| Tester Connection | Switch Condition | Specified condition |
| J16-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| J16-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the driver side - side airbag sensor and driver side rear airbag sensor.
Using a service wire, connect terminals 2 and 1 of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J17-1 (BCL+) - J17-2 (BCL-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| J16-1 (BCR+) - J16-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from the connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J17-1 (BCL+) - J17-2 (BCL-) | Always | 1 MΩ or higher |
| J17-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| J17-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J16-1 (BCR+) - J16-2 (BCR-) | Always | 1 MΩ or higher |
| J16-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| J16-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK DRIVER SIDE REAR AIRBAG SENSOR |
![]() |
Interchange the front passenger side rear airbag sensor with driver side rear airbag sensor and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1632, B1633, B1637 and B1638 are not output | A |
| DTC B1637 or B1638 is output | B |
| DTC B1632 or B1633 is output | C |
|
| ||||
|
| ||||
| C | ||
| ||