DTC C1415 Rear Speed Sensor RH Output Malfunction |
DTC C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1416 Rear Speed Sensor LH Output Malfunction |
| DTC NO. | DTC Detection Condition | Trouble Area |
| C1415 C1416 | Any of the following is detected:
|
|
| C1277 C1278 | Detected only during Test Mode. | Rear axle hub and bearing assembly RH/LH (speed sensor rotor) |
| 1.READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Speed Open | RR speed sensor open detection / Error or Normal | Error: Momentary interruption Normal: Normal | - |
| RL Speed Open | RL speed sensor open detection / Error or Normal | Error: Momentary interruption Normal: Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Wheel Speed | RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs (C1415 and C1416) are not output | A |
| DTCs (C1415 and/or C1416) are output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
![]() |
Check the speed sensor installation.
| *1 | Rear Speed Sensor |
| *a | No clearance |
| *b | OK |
| *c | NG |
|
| ||||
| OK | |
| 6.INSPECT SKID CONTROL SENSOR WIRE |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control sensor wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Z1-2 - ZJ3-1 | Always | Below 1 Ω |
| Z1-1 - ZJ3-2 | Always | Below 1 Ω |
| Z1-2 - ZJ3-2 | Always | 10 kΩ or higher |
| Z1-2 - Body ground | Always | 10 kΩ or higher |
| Z1-1 - ZJ3-1 | Always | 10 kΩ or higher |
| Z1-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| a1-2 - aJ3-1 | Always | Below 1 Ω |
| a1-1 - aJ3-2 | Always | Below 1 Ω |
| a1-2 - aJ3-2 | Always | 10 kΩ or higher |
| a1-2 - Body ground | Always | 10 kΩ or higher |
| a1-1 - aJ3-1 | Always | 10 kΩ or higher |
| a1-1 - Body ground | Always | 10 kΩ or higher |
| *1 | Skid Control Sensor Wire |
| *a | RH |
| *b | LH |
Reconnect the rear speed sensor wire.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A76 brake actuator assembly (skid control ECU) connector and the Z1 and/or a1 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A76-17 (RR+) - Z1-2 | Always | Below 1 Ω |
| A76-16 (RR-) - Z1-1 | Always | Below 1 Ω |
| A76-5 (RL+) - a1-2 | Always | Below 1 Ω |
| A76-4 (RL-) - a1-1 | Always | Below 1 Ω |
| A76-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A76-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| A76-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A76-4 (RL-) - Body ground | Always | 10 kΩ or higher |
Reconnect the A76 brake actuator assembly (skid control ECU) connector and the rear speed sensor connector.
|
| ||||
| OK | |
| 8.CHECK BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Z1-2 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| a1-2 - Body ground | Ignition switch ON | 8 to 14 V |
| *a | Front view of wire harness connector (to Rear Speed Sensor) |
| *b | RH |
| *c | LH |
Reconnect the Z1 and/or a1 rear speed sensor connector.
|
| ||||
| OK | |
| 9.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs (C1415 and C1416) are not output | A |
| DTCs (C1415 and/or C1416) are output | B |
|
| ||||
| A | ||
| ||
| 10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY |
Turn the ignition switch off.
Replace the rear speed sensor and rear axle hub and bearing assembly (Click here).
| NEXT | |
| 11.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs (C1415 and C1416) are not output | A |
| DTCs (C1415 and/or C1416) are output | B |
|
| ||||
| A | ||
| ||