Home › Engine / Hybrid System ยท 2NZ-FE › INTAKE / EXHAUST › EXHAUST PIPE

EXHAUST PIPE > INSTALLATION

for Preparation Click here



1. INSTALL EXHAUST TAIL PIPE BAFFLE SUB ASSEMBLY (w/ Side Mudguard)


    A173892E01
  1. Align the keyway on a new tail exhaust pipe baffle sub-assembly with the protruding part of the exhaust tail pipe as shown in the illustration.
    Text in Illustration 
    *1
    Plastic Hammer
    *a
    Protruding Part
    *b
    Keyway

  1. Using a plastic hammer, uniformly tap in the tail exhaust pipe baffle sub-assembly.



2. INSTALL EXHAUST PIPE GASKET


    A128852E04
  1. Using a plastic hammer and a wooden block, tap in a new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
    Text in Illustration 
    *1
    Exhaust Pipe Gasket
    *2
    Wooden Block
    *3
    Plastic Hammer
    *4
    Exhaust Manifold

    NOTICE:
    1. Install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket by dropping it, etc.
    4. Do not damage the outer surface of the gasket.
    5. Do not push in the gasket with the exhaust pipe when connecting it.



3. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A128853
  1. Using a vernier caliper, measure the free length of the compression springs.

    Minimum length:
    41.5 mm (1.634 in.)

    If the length is not as specified, replace the compression spring.

  1. Hang the front exhaust pipe assembly with the 3 exhaust pipe supports.



    A247549E01
  1. Install the front exhaust pipe sub-assembly onto the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.
    Text in Illustration 
    *1
    Exhaust Manifold
    *2
    Front Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 8.5 mm (0.335 in.)

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    HINT:
    After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



4. INSTALL NO. 2 EXHAUST PIPE GASKET


    A128852E04
  1. Install the No. 2 exhaust pipe gasket to the front exhaust pipe assembly.
    Text in Illustration 
    *1
    No. 2 Exhaust Pipe Gasket
    *2
    Wooden Block
    *3
    Plastic Hammer
    *4
    Front Exhaust Pipe Assembly



5. INSTALL TAIL EXHAUST PIPE ASSEMBLY


    A128853
  1. Using a vernier caliper, measure the free length of the compression springs.

    Minimum length:
    38.5 mm (1.516 in.)

    If the length is not as specified, replace the compression spring.

  1. Hang the front exhaust pipe assembly with the 2 exhaust pipe supports.



    A247551E01
  1. Install the tail exhaust pipe assembly onto the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
    Text in Illustration 
    *1
    Front Exhaust pipe Assembly
    *2
    Tail Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 6.5 mm (0.256 in.)

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    HINT:
    After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



6. INSTALL FRONT FLOOR CENTER BRACE (w/ Side Mudguard)
  1. Install the front floor center brace onto the body with the 2 bolts.

    Torque:
    30 N*m{ 307 kgf*cm , 22 ft.*lbf }



7. INSTALL NO. 2 OXYGEN SENSOR (for Sensor 2)
(Click here)


8. INSPECT FOR EXHAUST GAS LEAK