WINDSHIELD GLASS > INSTALLATION |
| 1. CLEAN WINDSHIELD GLASS |
![]() |
Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.
Clean the outer edge of the windshield glass with a non-residue solvent.
| 2. INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
Using a brush or sponge, coat the application area of the No. 2 windshield glass stoppers with Primer G.
Install 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.

| *a | Back Side | *b | Ceramic Notch |
| *c | 7.6 mm (0.299 in.) | *d | 40 mm (1.575 in.) |
| 3. INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
![]() |
Install 2 new No. 1 windshield glass stoppers to the vehicle body, as shown in the illustration.
| *1 | No. 1 Windshield Glass Stopper |
| 4. INSTALL WINDOW GLASS ADHESIVE DAM |
Using a brush or sponge, coat the application area of adhesive dam with Primer G.
Install a new adhesive dam onto the windshield glass, as shown in the illustration.

| *a | Back Side | *b | 9.6 mm (0.378 in.) |
| *c | 42.2 mm (1.661 in.) | - | - |
| 5. INSTALL WINDSHIELD GLASS |
![]() |
Clean and shape the contact surface of the vehicle body.
| *1 | Adhesive |
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
![]() |
Position the windshield glass.
| *a | Mark |
Using suction cups, place the windshield glass in the correct position.
Check that the whole contact surface of the windshield glass rim is perfectly even.
Align the matchmarks on the windshield glass and vehicle body.
Remove the windshield glass.
![]() |
Using a brush, coat the installation surface on the vehicle body with Primer M.
| *1 | Primer M |
| *2 | Adhesive |
| *a | Correct |
| *b | Incorrect |
Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

| *1 | Primer G | - | - |
| *a | Back Side | *b | 8 mm (0.315 in.) |
| *c | 19 mm (0.748 in.) | - | - |
Apply adhesive to the glass.
![]() |
Cut off the tip of the cartridge nozzle, as shown in the illustration.
| *a | 8.0 mm (0.315 in.) |
| *b | 12.0 mm (0.472 in.) |
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with a cartridge.
Apply adhesive to the windshield glass, as shown in the illustration.

| *1 | Adhesive | - | - |
| *a | Back Side | *b | 3.0 mm (0.118 in.) |
| *c | 12.0 mm (0.472 in.) | *d | 8.0 mm (0.315 in.) |
| *e | 30.5 mm (1.201 in.) | - | - |
Install the windshield glass.
![]() |
Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
| *a | Mark |
Lightly press the front surface of the windshield glass to ensure a close fit.
![]() |
If necessary, use a scraper to correct the level or position of adhesive that has been applied.
| *1 | Windshield |
| *2 | Dam |
| *3 | Adhesive |
| 6. INSTALL WINDSHIELD OUTSIDE MOULDING |
![]() |
Using a brush or sponge, coat the application area of the moulding with Primer G.
Install a new moulding onto the windshield glass, as shown in the illustration.

![]() |
Hold the windshield glass using Hold the windshield glass using protective tape until applied adhesive hardens. until applied adhesive hardens.
| *1 | Protective Tape |
| Temperature | Minimum Time Prior to Driving Vehicle |
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
| 7. INSPECT FOR LEAK AND REPAIR |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 8. INSTALL ROOF HEADLINING ASSEMBLY (for 5 Door) |
| 9. INSTALL ROOF HEADLINING ASSEMBLY (for 3 Door) |
| 10. INSTALL INNER REAR VIEW MIRROR ASSEMBLY |
| 11. INSTALL WINDSHIELD WIPER MOTOR AND LINK |