Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for 3 Door)

ROOF HEADLINING (for 3 Door) > INSTALLATION

for Preparation Click here



1. INSTALL ROOF HEADLINING ASSEMBLY


    B284340
  1. Pull the roof headlining back into the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.

  1. Engage the 2 hooks and install the roof headlining.

  1. Install the 3 clips.

  1. Engage the 2 claws.

  1. for front pillar RH side:

    1. Install the 4 clamps.

    2. Connect the connector.

  1. for front pillar LH side:

    1. Install the 4 clamps.

    2. Connect the connector.

  1. for rear pillar RH side:

    1. Install the 3 clamps.

    2. Connect the connector.



2. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY
  1. Install the rear center seat outer belt with the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }

  1. Engage the 2 claws and close the slip joint cover.



3. INSTALL MAP LIGHT ASSEMBLY
  1. Connect the connector.



    E222167
  1. Engage the 4 claws to install the map light assembly.



4. INSTALL ASSIST GRIP ASSEMBLY

HINT:
Use the same procedure to install all assist grips.

  1. Engage the 2 clips and install the assist grip.



    B114352
  1. Engage the 4 claws and install the 2 assist grip covers.



5. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/ Cover)

HINT:
Use the same procedure to install all roof headlining service hole covers.

  1. Install the 2 roof headlining service hole covers.



6. INSTALL VISOR HOLDER


    B170213E02
  1. Engage the 2 claws and turn the visor holder counterclockwise 45° to install it.

    HINT:
    Use the same procedure for the RH side and LH side.



7. INSTALL VISOR ASSEMBLY RH
  1. Install the visor with the 2 screws.

  1. Install the visor shaft into the visor holder.



8. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



9. INSTALL REAR ROOF SIDE RAIL GARNISH RH
  1. Engage the 4 clips and install the roof side rail garnish.



10. INSTALL REAR ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.



11. INSTALL ROOF SIDE INNER GARNISH RH
  1. Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish.

  1. Engage the 5 clips and install the roof side inner garnish.



12. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



13. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 3 clips and the 3 claws and install the deck trim side panel.

  1. Install the 3 screws.



14. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



15. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
  1. Engage the 2 claws and install the rear seat 3 point type outer belt.

  1. Tighten the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }



16. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



17. INSTALL REAR FLOOR FINISH PLATE
  1. Engage the 4 guides and the 4 claws to install the rear floor finish plate.



18. INSTALL JACK HANDLE


19. INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
  1. Connect the connector.



    E222046
  1. Engage the claw to install the No. 2 room light assembly.



20. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
  1. Remove the piece of cloth or nylon.

  1. for 6 speakers:

    1. Connect the connector.



    B284321E01
  1. Make sure that the front pillar garnish clip is not damaged.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    1. If there is any damage, replace the garnish clip with a new one.
    2. When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

  1. Engage the 2 guides.

  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish.

    HINT:
    Tape the needle-nosed pliers tip before use.



    B284391E01
  1. Engage the clip and the front pillar garnish clip to install the front pillar garnish.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip



21. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

HINT:
Use the same procedure as for the RH side.



22. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
  1. for 6 speakers:

    1. Connect the connector.

  1. Engage the 2 guides and the 2 clips and install the front pillar garnish.



23. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

HINT:
Use the same procedure as for the RH side.



24. INSTALL CENTER PILLAR UPPER GARNISH RH
  1. Pass the front seat outer belt through the slit in the center pillar upper garnish.

  1. Engage the clip and install the center pillar upper garnish with 2 screws.



25. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.



26. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
  1. Engage the 8 clips and the 10 claws.

  1. Engage the 3 guides and install the quarter trim panel.



27. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



28. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH
  1. Connect the floor anchor part of the front seat outer belt assembly and install the front seat belt outer bar sub-assembly with the 2 bolts.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }



29. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B284341E01
  1. Align the paint mark on the front door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Flange Position

    Paint Mark:
    Area
    Color
    RH Side
    Yellow
    LH Side
    White

    NOTICE:
    After installation, check that the corners fit correctly.



31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



32. INSTALL COWL SIDE TRIM BOARD RH
  1. Engage the clip.

  1. Install the cowl side trim board with clip.



33. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



34. INSTALL FRONT DOOR SCUFF PLATE RH
  1. Engage the 8 claws and install the front door scuff plate.



35. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



36. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


37. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


38. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


39. INSTALL SPARE WHEEL COVER
  1. Install the spare wheel cover.



40. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board.