KNEE AIRBAG ASSEMBLY > DISPOSAL |
![]() |
| 1. DISPOSE OF LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Remove the No. 1 instrument panel under cover sub-assembly.
Disconnect cable from negative battery terminal.
Remove the No. 1 instrument panel under cover sub-assembly .
Disconnect the airbag connector.
![]() |
Using a screwdriver with its tip wrapped in protective tape, release the locking button.
| *1 | Locking Button |
| *2 | Protective Tape |
Disconnect the airbag connector.
![]() |
Connect SST.
Connect the SST connector to the lower No. 1 instrument panel airbag assembly.
![]() |
Push in the locking button.
| *1 | Locking Button |
![]() |
Move SST to at least 10 m (33 ft.) away from the vehicle.
| *1 | Battery |
Close all doors and windows of the vehicle.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 2. DISPOSE OF LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (When not Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Remove the lower No. 1 instrument panel airbag assembly (Click here).
![]() |
Using a braided wire harness, tie the lower No. 1 instrument panel airbag assembly to the tire.
| *a | Stripped Wire Harness Section |
| Area | Measurement |
| A | 1.25 mm2 or more (0.00192 in.2 or more) |
Position the lower No. 1 instrument panel airbag assembly inside the tire, as shown in the illustration.

| Area | Measurement |
| A | 360 mm (14.17 in.) |
| B | 185 mm (7.28 in.) |
Connect SST.
![]() |
Connect the SST connector to the lower No. 1 instrument panel airbag assembly.
| *1 | Locking Button |
Push in the locking button.
![]() |
Place the tires.
| *1 | Tire (2 or more) |
Place at least 2 tires under the tire to which the lower No. 1 instrument panel airbag assembly is tied.
Place at least 2 tires over the tire to which the lower No. 1 instrument panel airbag assembly is tied. A disc wheel should be installed onto the top tire.
![]() |
Tie the tires together with 2 wire harnesses.
![]() |
Connect SST.
| *1 | Battery |
Deploy the airbag.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Check that no one is within a 10 m (33 ft.) radius of the tire to which the lower No. 1 instrument panel airbag assembly is tied.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the lower No. 1 instrument panel airbag assembly.
| *1 | Plastic Bag |
Remove the lower No. 1 instrument panel airbag assembly from the tire.
Place the lower No. 1 instrument panel airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.