CURTAIN SHIELD AIRBAG ASSEMBLY (for 3 Door) > DISPOSAL |
![]() |
| 1. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
![]() |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Remove the roof headlining (Click here).
![]() |
Using a thin-bladed screwdriver with its tip wrapped with protective tape, release the locking button.
| *1 | Protective Tape |
| *2 | Locking Button |
Disconnect the airbag connector.
![]() |
Connect SST.
After connecting SST, connect it to the curtain shield airbag assembly.
Push in the locking button.
![]() |
Move SST to at least 10 m (33 ft.) away from the vehicle.
| *1 | Battery |
Close all doors and windows of the vehicle.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Deploy the curtain shield airbag assembly.
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press the SST activation switch and deploy the curtain shield airbag assembly.
| 2. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When not Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
![]() |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Remove the curtain shield airbag assembly (Click here).
![]() |
Cut off the deployment section of the curtain shield airbag assembly.
| *a | Cut |
![]() |
Using a T25 "TORX" socket wrench, remove the screw.
![]() |
Connect SST.
| *1 | Locking Button |
After connecting SST, connect it to the curtain shield airbag assembly.
Push in the locking button.
![]() |
Using a braided wire harness, tie the curtain shield airbag assembly to the tire.
| *a | Stripped Wire Harness Section |
| Area | Measurement |
| A | 1.25 mm2 or more (0.00192 in.2 or more) |
![]() |
Position the curtain shield airbag assembly inside the tire, as shown in the illustration.
| Area | Measurement |
| A | 185 mm (7.28 in.) |
| B | 360 mm (14.17 in.) |
![]() |
Place the tires.
| *1 | Tire (2 or more) |
Place at least 2 tires under the tire to which the curtain shield airbag assembly is tied.
Place at least 2 tires over the tire to which the curtain shield airbag assembly is tied. The disc wheel should be installed onto the top tire.
![]() |
Tie the tires together with 2 wire harnesses.
![]() |
Connect SST.
| *1 | Battery |
Deploy the curtain shield airbag assembly.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Check that no one is within a 10 m (33 ft.) radius of the tire to which the curtain shield airbag assembly is tied.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the curtain shield airbag assembly.
| *1 | Plastic Bag |
Remove the curtain shield airbag assembly from the tire.
Place the curtain shield airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.