ROOF HEADLINING (for 3 Door) > REMOVAL |
| 1. REMOVE DECK BOARD ASSEMBLY |
![]() |
Remove the deck board.
| 2. REMOVE SPARE WHEEL COVER |
![]() |
Remove the spare wheel cover.
| 3. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side) |
| 4. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side) |
| 5. REMOVE REAR SEATBACK ASSEMBLY (for Fold Down Seat Type) |
| 6. REMOVE FRONT DOOR SCUFF PLATE RH |
![]() |
Disengage the 8 claws and remove the front door scuff plate.
| 7. REMOVE FRONT DOOR SCUFF PLATE LH |
| 8. REMOVE COWL SIDE TRIM BOARD RH |
![]() |
Remove the clip.
Disengage the clip and remove the cowl side trim board.
| 9. REMOVE COWL SIDE TRIM BOARD LH |
| 10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip.
| 11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 12. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH |
![]() |
Remove the 2 bolts and front seat belt outer bar sub-assembly, disconnect the floor anchor part of the front seat outer belt assembly.
| 13. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH |
| 14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
![]() |
Disengage the 8 clips and 10 claws.
Disengage the 3 guides and remove the quarter trim panel.
| 15. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH |
| 16. REMOVE CENTER PILLAR UPPER GARNISH RH |
![]() |
Remove the 2 screws and disengage the clip.
Pass the front seat outer belt through the slit in the center pillar upper garnish and remove the center pillar upper garnish.
| 17. REMOVE CENTER PILLAR UPPER GARNISH LH |
| 18. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag) |
![]() |
Disengage the front pillar garnish clip and the clip.
| *1 | Front Pillar Garnish Clip |
![]() |
Using needle nose pliers, turn the front pillar garnish clip 90° and disengage it from the front pillar garnish.
| *1 | Protective Tape |
Disengage the 2 guides and remove the front pillar garnish.
for 6 speakers:
Disconnect the connector.
![]() |
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.
| 19. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag) |
| 20. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag) |
![]() |
Disengage the 2 clips and the 2 guides and remove the front pillar garnish.
for 6 speakers:
Disconnect the connector.
| 21. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag) |
| 22. REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw.
| *1 | Protective Tape |
Disconnect the connector and remove the No. 2 room light assembly.
| 23. REMOVE JACK HANDLE |
| 24. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Disengage the 4 claws and 4 guides and remove the rear floor finish plate.
| 25. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH |
![]() |
Remove the bolt.
Disengage the 2 claws and separate the rear seat 3 point type outer belt.
| 26. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
| 27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH |
![]() |
Remove the 3 screws.
Disengage the 3 clips and the 3 claws and remove the deck trim side panel.
| 28. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
| 29. REMOVE ROOF SIDE INNER GARNISH RH |
![]() |
Disengage the 5 clips.
Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
| 30. REMOVE ROOF SIDE INNER GARNISH LH |
| 31. REMOVE REAR ROOF SIDE RAIL GARNISH RH |
![]() |
Disengage the 4 clips and remove the roof side rail garnish.
| 32. REMOVE REAR ROOF SIDE RAIL GARNISH LH |
| 33. REMOVE VISOR ASSEMBLY RH |
![]() |
Remove the visor shaft from the visor holder.
Remove the 2 screws and the visor.
| 34. REMOVE VISOR ASSEMBLY LH |
| 35. REMOVE VISOR HOLDER |
![]() |
Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.
| 36. REMOVE ASSIST GRIP ASSEMBLY |
![]() |
Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.
![]() |
Disengage the 2 clips and remove the assist grip.
| 37. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/ Cover) |
![]() |
Using a clip remover, remove the 2 roof headlining service hole covers.
| 38. REMOVE MAP LIGHT ASSEMBLY |
![]() |
Using a moulding remover, disengage the 4 claws.
Disconnect the connector and remove the map light assembly.
| 39. SEPARATE REAR CENTER SEAT OUTER BELT ASSEMBLY |
![]() |
Disengage the 2 claws and open the slip joint cover.
![]() |
Remove the bolt and separate the rear center seat outer belt.
| 40. REMOVE ROOF HEADLINING ASSEMBLY |

| *a | Front Pillar RH Side | *b | Front Pillar LH Side |
| *c | Rear Pillar RH Side | - | - |
for front pillar RH side:
Disconnect the connector
Using a clip remover, remove the 4 clamps.
for front pillar LH side:
Disconnect the connector
Using a clip remover, remove the 4 clamps.
for rear pillar RH side:
Disconnect the connector
Using a clip remover, remove the 3 clamps.
Disengage the 2 claws.
Using a clip remover, remove the 3 clips.
Disengage the 2 hooks.
![]() |
Remove the roof headlining from the vehicle through the back door as shown in the illustration.