Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

for Preparation Click here


DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake and valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E31


DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in camshaft timing oil control valve assembly circuit
(1 trip detection logic)
  1. Open or short in camshaft timing oil control valve assembly circuit
  2. Camshaft timing oil control valve assembly
  3. ECM

HINT:
These DTCs relate to the camshaft timing oil control valve assembly.


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Wait 5 seconds or more.
  6. Enter the following menus: Powertrain / Engine and ECT / DTC.
  7. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  8. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  9. Input the DTC: P0010.
  10. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.


WIRING DIAGRAM


A254073E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR DTC
  1. Clear DTCs after recording the freeze frame data and DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine and allow it to idle. Then check for DTCs.

  1. Check that P0010 is not output.

    OK:
    P0010 is not output.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
  1. Disconnect the camshaft timing oil control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B63-1 - B84-100 (OC1+)
    Always
    Below 1 Ω
    B63-2 - B84-123 (OC1-)
    Always
    Below 1 Ω
    B63-1 or B84-100 (OC1+) - Body ground
    Always
    10 kΩ or higher
    B63-2 or B84-123 (OC1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)