Home › Engine / Hybrid System ยท 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

DTC    P0116    Engine Coolant Temperature Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC No.
DTC Detection Condition
Trouble Area
P0116
Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a) and (b) met (2 trip detection logic):
  1. (a) Vehicle driven at varying speeds (accelerated and decelerated)
  2. (b) Engine coolant temperature remains within 3°C (5.4°F) of initial engine coolant temperature
  1. Thermostat
  2. Engine coolant temperature sensor

MONITOR DESCRIPTION

When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.

MONITOR STRATEGY


Required Sensors/Components (Main)
Engine coolant temperature sensor
Required Sensors/Components (Related)
None
Frequency of Operation
Once per driving cycle

CONFIRMATION DRIVING PATTERN


A254128E02

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
  4. Check that the coolant temperature is 60°C (140°F) or less.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Turn the ignition switch off and wait for at least 30 seconds.
  7. Turn the ignition switch to ON and turn the tester on [A].
  8. Start the engine.
  9. Drive the vehicle at varying speeds (accelerated and decelerated more than 10 times) for 5 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the driving pattern can be resumed.

  10. Enter the following menus: Powertrain / Engine and ECT / DTC [C].
  11. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P0116.
  14. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.


INSPECTION PROCEDURE

HINT:
  1. If any of DTCs P0115, P0117 or P0118 are stored simultaneously with DTC P0116, the ECT sensor may have an open or a short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. When the DTC is output, check the engine coolant temperature using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.


Result 
Result
Proceed to
DTC P0116 is output
A
DTC P0116 and other DTCs are output
B

HINT:
If any DTCs other than P0116 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT THERMOSTAT
  1. Inspect thermostat (Click here).



NG
REPLACE THERMOSTAT (Click here)
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)