Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0136    Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

for Preparation Click here


DESCRIPTION

Refer to P0031 .

HINT:
Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.


DTC No.
DTC Detection Condition
Trouble Area
P0136
Following conditions (a) and (b) met for 4 minutes or more after engine warmed up (2 trip detection logic):
  1. (a) Vehicle driven in 1 STOP-and-GO* cycles
  2. (b) Heated oxygen sensor (sensor 2) voltage remains at 0.4 V or more or 0.5 V or less.
  1. Open or short in heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Heated oxygen sensor (sensor 2) heater
  4. No. 1 integration relay (EFI relay)
All of following conditions (a), (b), (c), (d) and (e) met (2 trip detection logic):
  1. (a) Cumulative sensor monitoring time 85 seconds or more
  2. (b) Cumulative time while rear heated oxygen sensor voltage less than 0.05 V 60 seconds or more
  3. (c) Cumulative time while rear heated oxygen sensor voltage 0.7 V or more less than 17 seconds
  4. (d) Cumulative time while rear heated oxygen sensor voltage 0.45 V or more less than 17 seconds
  5. (e) Maximum continuous time while rear heated oxygen sensor voltage 0.45 V or more less than 20 seconds

HINT:
*: STOP refers to a vehicle speed of less than 5 km/h (3.1 mph) and GO refers to a vehicle speed of 100 km/h (62.5 mph) or more.


MONITOR DESCRIPTION

The ECM monitors the heated oxygen sensor (sensor 2) to check for the following malfunctions. If any of the malfunctions are detected, the ECM illuminates the MIL and stores a DTC.
  1. The heated oxygen sensor (sensor 2) output voltage remains above 0.5 V (rich) or below 0.4 V (lean) while the vehicle is accelerated and decelerated for 4 minutes or more.
  2. The heated oxygen sensor (sensor 2) output voltage remains extremely low, below 0.05 V for a long time period of time while the vehicle is driven.

MONITOR STRATEGY


Required Sensor/Components (Main)
Heated oxygen sensor (sensor 2)
Required Sensor/Components (Related)
Engine coolant temperature sensor, Mass air flow meter, vehicle speed sensor, Throttle with motor body assembly
Frequency of operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Heated oxygen sensor output voltage: 
All of the following conditions A to C are met
-
A. Engine
Running
B. Time after engine starts
0 seconds or more
C. Cumulative time while heated oxygen sensor is ON
22 seconds or more

Heated oxygen sensor output voltage (crack): 
All of the following conditions A to E are met
-
A. Engine
Running
B. Vehicle speed
3 km/h (1.864 mph) or higher
C. Idle
OFF
D. Fuel cut
OFF
E. Cumulative time while heated oxygen sensor heater is ON
120 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Heated oxygen sensor output voltage 
All of the following conditions are met
-
Frequency of switch time between less than 0.4 V and 0.5 V or more
0 times
Cumulative rear oxygen sensor monitor time
190 seconds or more

Heated oxygen sensor output voltage (crack) 
All of the following conditions A to E are met
-
A. Cumulative heated oxygen sensor monitoring time
85 seconds or more
B. Cumulative time while heated oxygen sensor voltage is below 0.05 V
60 seconds or more
C. Cumulative time while heated oxygen sensor voltage is 0.7 V or higher
Less than 17 seconds
D. Cumulative time while heated oxygen sensor voltage is 0.45 V or higher
Less than 17 seconds
E. Maximum time while heated oxygen sensor voltage is 0.45 V or higher
Less than 20 seconds

CONFIRMATION DRIVING PATTERN


A260198E01

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch on and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch and turn the tester on.
  6. Start the engine and idle it for 60 seconds or more [A].
  7. Drive the vehicle at more than 100 km/h (62.5 mph) for 5 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Allow the engine to idle for 10 seconds or more [C].
  9. Enter the following menus: Powertrain / Engine and ECT / DTC [D].
  10. Read pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0136.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F].


WIRING DIAGRAM

Refer to P0031 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
  5. Perform the Active Test operation with the engine idling.
  6. Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display
(Sensor)
Injection Volume
Status
Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V

NOTICE:
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


Case
Heated Oxygen Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E05
A150789E07
A150787E05
A150788E09
-
2
A150787E05
A150790E01
A150787E05
A150788E09
  1. Heated oxygen sensor (Sensor 1)
  2. Heated oxygen sensor heater (Sensor 1)
  3. Heated oxygen sensor circuit (Sensor 1)
3
A150787E05
A150789E07
A150787E05
A150790E01
  1. Heated oxygen sensor (Sensor 2)
  2. Heated oxygen sensor heater (Sensor 2)
  3. Heated oxygen sensor circuit (Sensor 2)
4
A150787E05
A150790E01
A150787E05
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)

HINT:
  1. Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both heated oxygen sensors
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2, then press the view button.
  3. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be stored.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0136)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0136 is output
    A
    DTC P0136 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0136 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (O2S B1S2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2.

  1. Allow the engine to run at 2500 rpm for 3 minutes.

  1. Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.

    Standard Voltage:
    Heated oxygen sensor voltage alternates between below 0.4 V and higher than 0.5 V.


A128474E12


Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 7
A


3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 2))
  1. Inspect the heated oxygen sensor (sensor 2) (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 2) (Click here)
OK


4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 2))
  1. Disconnect the heated oxygen sensor (sensor 2) connector.

  1. Turn the ignition switch to ON.



    A215512E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F80-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor (Sensor 2))



NG
Go to step 6
OK


5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)
  1. Disconnect the heated oxygen sensor (sensor 2) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    F80-1 (HT1B) - B84-47 (HT1B)
    Always
    Below 1 Ω
    F80-3 (OX1B) - B84-64 (OX1B)
    Always
    Below 1 Ω
    F80-4 (E2) - B84-87 (EX1B)
    Always
    Below 1 Ω
    F80-1 (HT1B) or B84-47 (HT1B) - Body ground
    Always
    10 kΩ or higher
    F80-3 (OX1B) or B84-64 (OX1B) - Body ground
    Always
    10 kΩ or higher
    F80-4 (E2) or B84-87 (EX1B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEATED OXYGEN SENSOR (SENSOR 2) (Click here)  

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR (SENSOR 2))
  1. Disconnect the heated oxygen sensor (sensor 2) connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    F80-2 (+B) - 1D-11
    Always
    Below 1 Ω
    F80-2 (+B) or 1D-11 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

7.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0136 is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HEATED OXYGEN SENSOR (SENSOR 2) (Click here)