FRONT SEAT SIDE AIRBAG ASSEMBLY (for Driver Side) > DISPOSAL |
![]() |
| 1. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connector from the front seat side airbag assembly under the front seat assembly.
Slide the slider to release the lock, and then disconnect the yellow airbag connector under the front seat assembly.

| *1 | Slider | - | - |
Connect SST.
![]() |
Connect the SST connector to the front seat side airbag assembly connector.
| *1 | Slider |
![]() |
Move SST at least 10 m (33 ft.) away from the front side window.
| *1 | Battery |
Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Deploy the front seat side airbag.
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 2. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When not Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Remove the front seat side airbag assembly (Click here).
![]() |
Using braided wire harness, tie down the front seat side airbag assembly to an unneeded tire.
| *a | Stripped Wire Harness Section |
| Area | Measurement |
| A | 1.25 mm2 (0.0019 in.2) or more |
![]() |
Install the 2 nuts to the front seat side airbag assembly.
![]() |
Wind the wires around the stud bolts of the front seat side airbag assembly as shown in the illustration.
![]() |
Position the front seat side airbag assembly inside the tire.
| Area | Measurement |
| A | 185 mm (7.28 in.) |
| B | 360 mm (14.17 in.) |
Connect SST.
![]() |
Connect the SST connector to the front seat side airbag assembly connector.
![]() |
Place the tires.
| *1 | Tires (2 or more) |
Place at least 2 tires under the tire to which the front seat side airbag assembly is tied.
Place at least 2 tires onto the tire to which the front seat side airbag assembly is tied. The top tire should have a wheel installed.
![]() |
Tie the tires together with the 2 wires.
Connect SST.
![]() |
Connect the SST connector.
| *1 | Battery |
Move SST at least 10 m (33 ft.) away from the airbag tied down to the tire.
Deploy the airbag.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Check that no one is within a 10 m (33 ft.) radius of the tire to which the front seat side airbag assembly is tied.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the front seat side airbag assembly.
| *1 | Plastic bag |
Remove the front seat side airbag assembly from the tire.
Place the front seat side airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.