DTC B1800/51 Short in Driver Side Squib Circuit |
DTC B1801/51 Open in Driver Side Squib Circuit |
DTC B1802/51 Short to GND in Driver Side Squib Circuit |
DTC B1803/51 Short to B+ in Driver Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1800/51 |
|
|
| B1801/51 |
| |
| B1802/51 |
| |
| B1803/51 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the steering pad, spiral cable sub-assembly and airbag sensor assembly.
Disconnect the connectors from the steering pad, spiral cable sub-assembly and airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the spiral cable sub-assembly connector (on the steering pad side) is not damaged.
Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
|
| ||||
| OK | |
| 2.CHECK STEERING PAD (DRIVER SIDE SQUIB) |
![]() |
Connect the instrument panel wire to the airbag sensor assembly and spiral cable sub-assembly.
Connect SST (resistance 2.1 Ω) to connector E.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Connector E |
| *a | Front view of wire harness connector (to Steering Pad (Driver Side Squib)) |
|
| ||||
| OK | ||
| ||
| 3.CHECK DRIVER SIDE SQUIB CIRCUIT |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect SST from connector E.
Disconnect the instrument panel wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z1-2 (D+) - Body ground | Ignition switch ON | Below 1 V |
| z1-1 (D-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z1-2 (D+) - z1-1 (D-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z1-2 (D+) - Body ground | Always | 1 MΩ or higher |
| z1-1 (D-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z1-2 (D+) - z1-1 (D-) | Always | 1 MΩ or higher |
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Connector E |
| *a | Front view of wire harness connector (to Steering Pad (Driver Side Squib)) |
Restore the released activation prevention mechanism of connector B to the original condition.
|
| ||||
| OK | |
| 4.CHECK DTC |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the steering pad and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE |
Restore the released activation prevention mechanism of connector B to the original condition.
![]() |
Disconnect the instrument panel wire from the spiral cable sub-assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F17-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| F17-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F17-1 (D+) - F17-2 (D-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F17-1 (D+) - Body ground | Always | 1 MΩ or higher |
| F17-2 (D-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F17-1 (D+) - F17-2 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector (to Spiral Cable Sub-assembly) |
|
| ||||
| OK | |
| 6.CHECK SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z1-2 (D+) - Body ground | Ignition switch ON | Below 1 V |
| z1-1 (D-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z1-2 (D+) - z1-1 (D-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z1-2 (D+) - Body ground | Always | 1 MΩ or higher |
| z1-1 (D-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z1-2 (D+) - z1-1 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
| *5 | Connector E |
| *a | Front view of wire harness connector (to Steering Pad (Driver Side Squib)) |
|
| ||||
| OK | ||
| ||