Home › Engine / Hybrid System · 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is stored, check the No. 1 ignition coil (No. 1 cylinder) circuit.
  3. If DTC P0352 is stored, check the No. 1 ignition coil (No. 2 cylinder) circuit.
  4. If DTC P0353 is stored, check the No. 1 ignition coil (No. 3 cylinder) circuit.
  5. If DTC P0354 is stored, check the No. 1 ignition coil (No. 4 cylinder) circuit.

A direct ignition system is used on this vehicle.
The direct ignition system is an ignition system in which each cylinder is ignited by its own No. 1 ignition coil and spark plug. The secondary wiring of each No. 1 ignition coil generates a powerful voltage which is applied directly to each spark plug. The spark passes from the center electrode of the spark plug to the ground electrode.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A256693E03


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT (1 to 4) circuit between No. 1 ignition coil and ECM
  3. No. 1 ignition coil (No.1 to No. 4 cylinder)
  4. ECM

  1. A033447E05
  2. Reference: Inspection using an oscilloscope
  3. While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

    ECM Terminal Name
    CH1: Between IGT (1 to 4) and E1
    CH2: Between IGF1 and E1
    Tester Range
    5 V/DIV., 20 ms./DIV.
    Condition
    Idling

MONITOR DESCRIPTION


A212405E14

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
No. 1 ignition coil
Required Sensors/Components (Related)
ECM
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / DTC.
  9. Read DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0351, P0352, P0353 or P0354.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform Confirmation Driving Pattern and the DTC judgment result again.


WIRING DIAGRAM


A254087E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
  1. Disconnect the No. 1 ignition coil connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B13-4 (GND) - Body ground
    Always
    Below 1 Ω
    B15-4 (GND) - Body ground
    Always
    Below 1 Ω
    B17-4 (GND) - Body ground
    Always
    Below 1 Ω
    B19-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NO. 1 IGNITION COIL (POWER SOURCE)


    A200905E24
  1. Disconnect the No. 1 ignition coil connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B13-1 (+B) - B13-4 (GND)
    Ignition switch ON
    11 to 14 V
    B15-1 (+B) - B15-4 (GND)
    Ignition switch ON
    11 to 14 V
    B17-1 (+B) - B17-4 (GND)
    Ignition switch ON
    11 to 14 V
    B19-1 (+B) - B19-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Ignition Coil)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
  1. Disconnect the No. 1 ignition coil connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B13-2 (IGF) - B84-81 (IGF1)
    Always
    Below 1 Ω
    B15-2 (IGF) - B84-81 (IGF1)
    Always
    Below 1 Ω
    B17-2 (IGF) - B84-81 (IGF1)
    Always
    Below 1 Ω
    B19-2 (IGF) - B84-81 (IGF1)
    Always
    Below 1 Ω
    B13-3 (IGT1) - B84-85 (IGT1)
    Always
    Below 1 Ω
    B15-3 (IGT2) - B84-84 (IGT2)
    Always
    Below 1 Ω
    B17-3 (IGT3) - B84-83 (IGT3)
    Always
    Below 1 Ω
    B19-3 (IGT4) - B84-82 (IGT4)
    Always
    Below 1 Ω
    B13-2 (IGF), B15-2 (IGF), B17-2 (IGF), B19-2 (IGF) or B84-81 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B13-3 (IGT1) or B84-85 (IGT1) - Body ground
    Always
    10 kΩ or higher
    B15-3 (IGT2) or B84-84 (IGT2) - Body ground
    Always
    10 kΩ or higher
    B17-3 (IGT3) or B84-83 (IGT3) - Body ground
    Always
    10 kΩ or higher
    B19-3 (IGT4) or B84-82 (IGT4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Shuffle arrangement of the No. 1 ignition coil (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Start the engine and run it at idle for 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    Same DTC is output
    A
    Different No. 1 ignition coil DTC is output
    B



B
REPLACE NO.1 IGNITION COIL
A

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)
  1. Disconnect the No. 1 ignition coil connectors.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
B13-1 (+B) - 1E-2
Always
Below 1 Ω
B15-1 (+B) - 1E-2
Always
Below 1 Ω
B17-1 (+B) - 1E-2
Always
Below 1 Ω
B19-1 (+B) - 1E-2
Always
Below 1 Ω
B13-1 (+B) or 1E-2 - Body ground
Always
10 kΩ or higher
B15-1 (+B) or 1E-2 - Body ground
Always
10 kΩ or higher
B17-1 (+B) or 1E-2 - Body ground
Always
10 kΩ or higher
B19-1 (+B) or 1E-2 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)