Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    C1425    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.
The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC No.
DTC Detection Condition
Trouble Area
C1425
When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body ground) continues for 3 seconds or more.
  1. Stop light switch circuit
  2. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


C243292E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
CHECK STOP LIGHT CIRCUIT (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    -

  1. Check that the stop light condition observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

Result 
Result
Proceed to
DTC C1425 is not output
A
DTC C1425 is output
B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)


    C243286E06
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A54-2 (STP) - Body ground
    Stop light switch ON
    (Brake pedal depressed)
    8 to 14 V
    Stop light switch OFF
    (Brake pedal released)
    Below 1.5 V

Text in Illustration 
*a
Front view of wire harness connector
(to Skid control ECU)
  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - STOP LIGHT CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)