Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Built-in Type Yaw Rate Sensor)

DTC    C1422    Master Cylinder Pressure Sensor Zero Point High Malfunction

for Preparation Click here


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU.

DTC No.
DTC Detection Condition
Trouble Area
C1422
When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
  1. Stop light switch
  2. Stop light switch circuit
  3. Master cylinder pressure sensor circuit
  4. Brake actuator assembly (Master cylinder pressure sensor)

WIRING DIAGRAM


C243291E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When C1425 is output together with C1422, inspect and repair the trouble areas indicated by C1425 first (Click here).

1.CHECK DTC
  1. Check the DTC C1425 is output (Click here).
    Result 
    Result
    Proceed to
    DTC C1425 is not output
    A
    DTC C1425 is output
    B



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menu: Chassis / ABS/VSC/TRC / Data List.

  1. In accordance with the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch/OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    -
    Master Cylinder Sensor
    Master cylinder pressure sensor reading/Min.: 0 V, Max.: 5 V
    0.3 to 0.9 V: When brake pedal is released
    Reading increases when brake pedal is depressed.

    Standard Voltage:
    Master cylinder pressure sensor reading is 0.86 V or less at the instant the stop light switch changes from off to on.



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC is recorded (Click here).

Result 
Result
Proceed to
DTC C1422 is not output
A
DTC C1422 is output
B


B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch installation. (Click here)

    OK:
    The brake pedal height and stop light switch installation are normal.



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH (Click here)
OK


5.INSPECT STOP LIGHT SWITCH
  1. Remove the stop light switch assembly (Click here).

  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A54-2 (STP) - A38-1
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)