DTC P0031 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |



| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 P0037 | Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip detection logic) |
|
| P0032 P0038 | Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic) |
|
| Required Sensors/Components (Main) | Heated oxygen sensor heater |
| Required Sensors/Components (Related) | Vehicle speed sensor |
| Frequency of Operation | Continuous |
| Battery voltage | 10.5 V or more |
| Engine | Running |
| Starter | OFF |
| Duration of following conditions | 2 seconds or more |
| Learned heater current during heater OFF | Completed |
| Duration of following conditions | 0.1 seconds or more |
| Learned heater current during heater OFF | Completed |
| Heated oxygen sensor heater current when heated oxygen sensor heater ON | Less than 0.25 A |
| Heated oxygen sensor heater current when heated oxygen sensor heater OFF | More than 2 A |
| Heated oxygen sensor heater current | 0.25 to 2 A (when idling with warm engine and battery voltage 11 to 14 V) |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect heated oxygen sensor.
|
| ||||
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR HEATER) |
![]() |
Disconnect the heated oxygen sensor (sensor 1 or 2) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B37-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| F80-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Heated Oxygen Sensor) |
| *b | for sensor 1 |
| *c | for sensor 2 |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor (sensor 1 or 2) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B37-1 (HT1A) - B84-109 (HT1A) | Always | Below 1 Ω |
| B37-1 (HT1A) or B84-109 (HT1A) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| F80-1 (HT1B) - B84-47 (HT1B) | Always | Below 1 Ω |
| F80-1 (HT1B) or B84-47 (HT1B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0037 OR P0038) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (Click here).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0031, P0032, P0037 or P0038 are output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY) |
Disconnect the heated oxygen sensor (sensor 1 or 2) connector.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B37-2 (+B) - 1E-4 | Always | Below 1 Ω |
| B37-2 (+B) or 1E-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| F80-2 (+B) - 1D-11 | Always | Below 1 Ω |
| F80-2 (+B) or 1D-11 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||