Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

If the rear RH side manual UP / DOWN function does not operate, a malfunction may exist in the rear power window regulator motor assembly RH, rear power window regulator switch assembly RH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B291670E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
  1. Inspect the rear power window regulator switch assembly RH (Click here).



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
  1. Inspect the rear power window regulator motor assembly RH (Click here).



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - P/W RELAY)
B291669E04
  1. Disconnect the I1 rear power window regulator switch assembly RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I1-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Power Window Regulator Switch Assembly RH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
  1. Disconnect the I1 rear power window regulator switch assembly RH connector.

  1. Disconnect the I2 rear power window regulator motor assembly RH connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I1-4 (U) - I2-1 (U)
    Always
    Below 1 Ω
    I1-1 (D) - I2-2 (D)
    Always
    Below 1 Ω
    I1-4 (U) - Body ground
    Always
    10 kΩ or higher
    I1-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
  1. for LHD

    1. Disconnect the I1 rear power window regulator switch assembly RH connector.

    2. Disconnect the H1 power window regulator master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I1-5 (SU) - H1-10 (U)
      Always
      Below 1 Ω
      I1-2 (SD) - H1-18 (D)
      Always
      Below 1 Ω
      I1-5 (SU) - Body ground
      Always
      10 kΩ or higher
      I1-2 (SD) - Body ground
      Always
      10 kΩ or higher

  1. for RHD

    1. Disconnect the I1 rear power window regulator switch assembly RH connector.

    2. Disconnect the G1 power window regulator master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I1-5 (SU) - G1-16 (U)
      Always
      Below 1 Ω
      I1-2 (SD) - G1-15 (D)
      Always
      Below 1 Ω
      I1-5 (SU) - Body ground
      Always
      10 kΩ or higher
      I1-2 (SD) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)