Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

DTC    B1244    Light Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.

DTC No.
DTC Detection Condition
Trouble Area
B1244
  1. Malfunction in automatic light control sensor.
  2. Open or short in automatic light control sensor circuit.
  1. Automatic light control sensor
  2. Main body ECU
  3. Harness or connector

WIRING DIAGRAM


E219666E01


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1244 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illumination Rate Info
    Illumination rate information/
    0 to 2162.65 ms
    Value output according to ambient light levels
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (Click here)  

3.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU)
  1. Disconnect the F73 automatic light control sensor connector.

  1. Disconnect the F76 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F73-3 (CLTB) - F76-20 (CLTB)
    Always
    Below 1 Ω
    F73-4 (CLTS) - F76-21 (CLTS)
    Always
    Below 1 Ω
    F73-5 (CLTE) - F76-22 (CLTE)
    Always
    Below 1 Ω
    F73-3 (CLTB) - Body ground
    Always
    10 kΩ or higher
    F73-4 (CLTS) - Body ground
    Always
    10 kΩ or higher
    F73-5 (CLTE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK MAIN BODY ECU
E219664E01
  1. Reconnect the main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F76-20 (CLTB) - F76-22 (CLTE)
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU)



NG
REPLACE MAIN BODY ECU (Click here)
OK


5.CHECK AUTOMATIC LIGHT CONTROL SENSOR


    E219665E01
  1. Reconnect the automatic light control sensor connector.

  1. Connect an oscilloscope to the automatic light control sensor connector.

  1. Check the waveform.

    OK:
    Tester Connection
    Tool Setting
    Switch Condition
    Specified Condition
    F73-4 (CLTS) - F73-5 (CLTE)
    5 V/DIV., 5 ms./DIV.
    Ignition switch ON, headlight dimmer switch in AUTO position
    Correct waveform is as shown

    HINT:
    When the ambient light becomes brighter, width A becomes narrower.

    Text in Illustration 
    *a
    Component with harness connected
    (Automatic Light Control Sensor)



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK

REPLACE MAIN BODY ECU (Click here)