Home › Drivetrain · U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0717    Turbine Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the input turbine. By comparing the input turbine speed signal (NT) with the speed sensor signal (SPD), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure in response to various conditions, thus performing smooth gear shifting.

DTC No.
DTC Detection Condition
Trouble Area
P0717
All conditions below are detected for 5 seconds or more (1 trip detection logic).
(a) Gear change is not being performed.
(b) Gear position: 3rd or 4th.
(c) T/M input shaft rpm: Less than 300 rpm.
(d) T/M output shaft rpm: 1000 rpm or more.
(e) Park/neutral position switch (NSW, R and L) is OFF.
(f) Shift solenoid valves, park/neutral position switch and vehicle speed sensor are in normal operation.
  1. Wire harness or connector
  2. Transmission revolution sensor (Speed sensor NT)
  3. Automatic transaxle (clutch, brake or gear etc.)
  4. ECM

MONITOR DESCRIPTION

The ECM detects the revolving signal from the transmission revolution sensor (input speed). The ECM outputs a gearshift signal by comparing the transmission revolution sensor signal with the speed sensor signal (SPD). While the vehicle is operating in the 3rd or 4th gear position in the shift position of D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is 1000 rpm*2 or more, the ECM detects the malfunction, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM


C243251E02


INSPECTION PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR INSTALLATION


    BR03795E86
  1. Check the transmission revolution sensor installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

    Text in Illustration 
    *a
    Correct
    *b
    Incorrect
    *c
    Clearance
    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ ABS)
    B
    NG (w/o ABS)
    C



B
SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR

C
SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR
A


2.INSPECT TRANSMISSION REVOLUTION SENSOR
C213110E06
  1. Disconnect the transmission revolution sensor connector from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (NT+) - 1 (NT-)
    20°C (68°F)
    560 to 680 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Revolution Sensor)
    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ ABS)
    B
    NG (w/o ABS)
    C



B
REPLACE TRANSMISSION REVOLUTION SENSOR (Click here)

C
REPLACE TRANSMISSION REVOLUTION SENSOR (Click here)
A


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)
C229165E26
  1. Connect the transmission revolution sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B84-125 (NT+) - B84-124 (NT-)
    20°C (68°F)
    560 to 680 Ω
    B84-125 (NT+) - Body ground
    Always
    10 kΩ or higher
    B84-124 (NT-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)