Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD)

BRAKE ACTUATOR (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE ACTUATOR BOLT CUSHION
  1. Install the 3 brake actuator bolt cushions to the brake actuator bracket assembly.

  1. Install the 3 brake actuator case collars to the brake actuator bolt cushion.



2. INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY


    C228795E01
  1. Install the actuator bracket with the 3 bolts in the sequence shown in the illustration.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.
    2. Do not carry an actuator by its connector.



3. INSTALL BRAKE ACTUATOR ASSEMBLY (w/o VSC)


    C169912E01
  1. Install the brake actuator with bracket with the 3 bolts in the sequence shown in the illustration.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not damage the brake tubes or wire harness.

  1. Using a union nut wrench 10 mm, connect the 6 brake tubes to the brake actuator assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



    C228100E02
  1. Connect the brake actuator connector.
    Text in Illustration 
    *1
    Lock Lever

    NOTICE:
    1. Make sure that the connector is locked securely.
    2. Make sure that the actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.



4. INSTALL BRAKE ACTUATOR ASSEMBLY (w/ VSC)


    C228794E01
  1. Install the brake actuator with bracket with the 3 bolts in the sequence shown in the illustration.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not damage the brake tubes or wire harness.

  1. Using a union nut wrench 10 mm and union nut wrench 12 mm, connect the 6 brake tubes to the brake actuator assembly.

    Torque:
    Flare Nut 10 mm:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    Flare Nut 12 mm:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



    C228100E02
  1. Connect the brake actuator connector.
    Text in Illustration 
    *1
    Lock Lever

    NOTICE:
    1. Make sure that the connector is locked securely.
    2. Make sure that the actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.



5. INSTALL BATTERY CARRIER
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Engage the 7 wire harness clamps and install the wire harness.



6. INSTALL BATTERY TRAY


7. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. BLEED BRAKE LINE
(Click here)


9. BLEED CLUTCH LINE (for Manual Transmission)
(Click here)


10. INSPECT ACTUATOR WITH INTELLIGENT TESTER
(Click here)


11. CHECK AND CLEAR DTC
(Click here)