CYLINDER HEAD GASKET > INSTALLATION |
| 1. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.
| *a | Measurement Length |
| 2. INSTALL CYLINDER HEAD GASKET |
![]() |
Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.
| *a | Lot No. |
| 3. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Apply a light coat of engine oil to the threads of the cylinder head bolts.
![]() |
Using several steps, install and tighten the 10 cylinder head bolts and plate washers uniformly with an 8 mm bi-hexagon wrench, in the sequence shown in the illustration.
Mark the front of the cylinder head bolt with paint.
![]() |
Retighten the cylinder head bolts 90° and then an additional by 90° as shown in the illustration.
| *a | Paint Mark |
Check that the paint mark is now at a 180° angle from the front.
![]() |
Apply a continuous bead of seal packing (Diameter 4.5 to 5.5 mm (0.177 to 0.217 in.)) as shown in the illustration.
| *1 | Cylinder Head |
| *2 | Cylinder Head Gasket |
| *3 | Cylinder Block |
| *a | Seal Packing |
| *b | Diameter: 4.5 to 5.5 mm |
| 4. INSTALL CAMSHAFT |
![]() |
Examine the front marks and numbers and check that the sequence is as shown in the illustration. Then provisionally tighten the 19 bolts.
![]() |
Uniformly tighten the bolts in several steps in the sequence shown in the illustration and install No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.
| *1 | No. 1 Bearing Cap |
| *2 | No. 2 Bearing Cap |
| 5. INSTALL CHAIN SUB-ASSEMBLY |
![]() |
Make sure that all the timing marks are in the positions (TDC) shown in the illustration.
| *a | Timing Marks |
| *b | Timing Mark |
![]() |
Set the timing mark of the crankshaft in a position between 40 and 140° ATDC, as illustrated.
| *a | Timing Mark |
| *b | 40° to 140° ATDC |
![]() |
Set the camshaft timing gear and the camshaft timing sprocket in the positions (20° ATDC) shown in the illustration.
| *a | 20° ATDC |
| *b | Timing Mark |
| *c | Timing Marks |
Set the crankshaft in the position (20° ATDC) shown in the illustration.
![]() |
Install the No. 1 chain vibration damper with the 2 bolts.
![]() |
Align the timing marks of the camshaft with the mark plates of the timing chain and install the timing chain.
| *a | Mark Plates |
| *b | Timing Marks |
| *c | Mark Plate |
| *d | Timing Mark |
| 6. INSTALL CHAIN TENSIONER SLIPPER |
![]() |
Install the chain tensioner slipper.
| 7. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the No. 1 chain tensioner assembly with the 2 bolts.
Remove the bar from the No. 1 chain tensioner assembly.
| 8. INSTALL OIL PUMP SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover.
| *1 | Splinter of Wood |
Apply a light coat of MP grease to the oil pump seal lip.
| 9. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install 2 new O-rings onto the 2 locations as shown in the illustration.
Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration.

| *a | Seal Packing | *b | Seal Width (Other Part) |
| *c | Seal Width (Water Pump Part) | - | - |
![]() |
Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.
![]() |
Install the oil pump assembly with the 15 bolts and the nut. Tighten the bolts and nut uniformly in several steps.
| 10. INSTALL ENGINE WATER PUMP ASSEMBLY |
Install the water pump assembly through a new water pump gasket with the 3 bolts and 2 nuts.
| 11. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
Install the transverse engine engine mounting bracket with the 4 bolts.
| 12. INSTALL WATER PUMP PULLEY |
Temporarily install the water pump pulley with the 3 bolts.
Using SST, hold the water pump pulley.
Tighten the 3 bolts to the specified torque.
| 13. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.
Apply a light coat of engine oil to the O-ring and install the camshaft timing oil control valve assembly with the bolt.
Connect the camshaft timing oil control valve assembly connector.
| 14. INSTALL CRANKSHAFT POSITION SENSOR |
Apply a light coat of engine oil to the O-ring.
Install the crankshaft position sensor with the bolt.
Connect the crankshaft position sensor connector.
| 15. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY |
Align the pin hole of the crankshaft damper with the pin and install the crankshaft damper sub-assembly.
Provisionally install the bolt.
Using 2 SST, tighten the bolt while holding the crankshaft damper sub-assembly.
| 16. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
Install the engine mounting insulator sub-assembly RH with the 4 bolts and 2 nuts.
| 17. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
![]() | Seal Packing |
Apply seal packing to the cylinder head as shown in the illustration.
![]() |
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.
for LHD:
Connect the connector and 4 wire harness clamps and connect the engine wire harness.
Install the wire harness bracket with the bolt.
for RHD:
Connect the connector and 3 wire harness clamps and connect the engine wire harness.
Connect the 4 fuel injector connectors.
| 18. INSTALL NO. 1 IGNITION COIL |
Install the 4 No. 1 ignition coils with the 4 bolts.
![]() |
| *1 | Body |
| *2 | Cap |
Connect the 4 No. 1 ignition coil connectors.
| 19. INSTALL FUEL VAPOR FEED HOSE ASSEMBLY |
Connect fuel vapor feed hose assembly.
| 20. INSTALL VENTILATION HOSE |
Connect the ventilation hose.
| 21. INSTALL GENERATOR ASSEMBLY |
| 22. INSTALL MANIFOLD SUPPORT BRACKET |
Install the manifold support bracket with the 3 bolts.
| 23. INSTALL EXHAUST PIPE GASKET |
| 24. INSTALL NO. 2 EXHAUST PIPE GASKET |
| 25. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
![]() |
Install the front exhaust pipe assembly onto the exhaust manifold with the 2 compression springs and 2 bolts.
| *1 | Exhaust Manifold |
| *2 | Front Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 8.5 mm (0.335 in.) |
| 26. CONNECT WIRE HARNESS |
Connect the wire harness with the 2 bolts.
| 27. CONNECT WATER BY-PASS HOSE |
Connect the water by-pass hose.
| 28. CONNECT INLET HEATER WATER HOSE A |
Connect inlet heater water hose A.
| 29. INSTALL NO. 1 WATER BY-PASS PIPE |
Install No. 1 water by-pass pipe with the bolt.
| 30. CONNECT HEATED OXYGEN SENSOR CONNECTOR |
Connect the heated oxygen sensor connector.
Install the sensor bracket with the bolt.
| 31. CONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR |
Connect the engine coolant temperature sensor connector.
| 32. CONNECT CAMSHAFT POSITION SENSOR CONNECTOR |
Connect the camshaft position sensor connector.
| 33. CONNECT BOOSTER VACUUM TUBE |
Connect the booster vacuum tube.
| 34. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
![]() | Push |
Insert the fuel tube connector into the fuel delivery pipe until a click sound can be heard.
Install the fuel pipe clamp.
| 35. INSTALL OIL LEVEL DIPSTICK GUIDE |
Apply engine oil to a new O-ring.
Install the O-ring onto the oil level dipstick guide.
Install the oil level dipstick guide with the bolt.
Engage the clamp and connect the wire harness to the oil level dipstick guide.
| 36. INSTALL INTAKE MANIFOLD |
Install a new gasket onto the intake manifold.
Install the intake manifold with the 3 bolts and 2 nuts.
Connect the 3 wire harness clamps shown in the illustration.
| 37. INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY |
| 38. CONNECT UNION TO CONNECTOR TUBE HOSE |
Connect the union to connector tube hose.
| 39. CONNECT VENTILATION HOSE |
Connect the ventilation hose.
| 40. INSTALL FUEL VAPOR FEED HOSE ASSEMBLY |
Install the fuel vapor feed hose assembly.
| 41. CONNECT THROTTLE WITH MOTOR BODY CONNECTOR |
Install the throttle with motor body connector bracket with the nut.
Connect the throttle with motor body connector.
Connect the wire harness clamp.
| 42. CONNECT NO. 2 WATER BY-PASS HOSE |
Connect No. 2 water by-pass hose.
| 43. INSTALL WATER FILLER SUB-ASSEMBLY |
Install the water filler sub-assembly with the 2 nuts.
Connect No. 1 radiator hose to the cylinder head.
| 44. CONNECT RESERVE TANK HOSE |
Connect the reserve tank hose.
| 45. CONNECT NO. 3 RADIATOR HOSE |
Connect No. 3 radiator hose.
| 46. INSTALL NO. 1 IGNITION COIL |
| 47. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE |
Install the air cleaner cap sub-assembly with No. 1 air cleaner hose to the throttle body assembly with the 2 clamps.
Tighten the hose clamp.
Engage the wire harness clamp and install the wire harness to the vacuum switching valve assembly.
Connect the vacuum switching valve assembly connector.
Connect the mass air flow meter connector.
Engage the wire harness clamp and install the wire harness to the air cleaner cap sub-assembly.
Connect the No. 2 fuel vapor feed hose to the intake manifold.
Install the fuel vapor feed hose to the No. 1 air cleaner hose.
Connect the fuel vapor feed hose assembly to the vacuum switching valve assembly and No. 1 air cleaner hose.
| 48. INSTALL BATTERY TRAY |
| 49. INSTALL BATTERY |
Install the battery onto the vehicle with the battery clamp.
Connect the cable to the battery terminal.
| 50. INSTALL OUTER COWL TOP PANEL (for LHD) |
Install the outer cowl top panel with the 8 bolts.
Engage the 2 clamps and install the wire harness.
| 51. INSTALL OUTER COWL TOP PANEL (for RHD) |
Install the outer cowl top panel with the 8 bolts.
Engage the 2 clamps and install the wire harness.
| 52. INSTALL INNER COWL TOP TO COWL BRACE (for LHD) |
Install the cowl top to cowl brace with the 2 bolts.
| 53. INSTALL INNER COWL TOP TO COWL BRACE (for RHD) |
Install the cowl top to cowl brace with the 2 bolts.
| 54. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD) |
Engage the clip and install the front No. 1 ventilator seal.
| 55. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD) |
Engage the clip and install the front No. 1 ventilator seal.
| 56. INSTALL FRONT AIR SHUTTER SEAL RH (for LHD) |
| 57. INSTALL FRONT AIR SHUTTER SEAL RH (for RHD) |
| 58. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY |
| 59. INSTALL FRONT WHEEL RH |
| 60. ADD ENGINE COOLANT |
Tighten the cylinder block drain cock plug and the radiator drain cock plug.
Pour engine coolant into the radiator assembly until it is full.
Check the coolant level inside the radiator assembly by squeezing the No. 2 radiator hose and the No. 3 radiator hose several times by hand. If the coolant level goes down, add engine coolant.
Install the water filler cap sub-assembly securely.
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens.
While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the No. 2 radiator hose and No. 3 radiator hose several times by hand to bleed air.
Stop the engine and wait until the coolant cools down.
If the coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the coolant level stays at the full level.
Recheck the coolant level inside the radiator reservoir tank assembly. If it is below the full level, add coolant.
| 61. ADD ENGINE OIL |
Add fresh engine oil.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL "energy-conserving", API grade SM "energy-conserving" or ILSAC multigrade engine oil |
|
| API grade SL or SM multigrade engine oil |
|
| Item | Capacity |
| Drain and refill with oil filter change | 3.7 liters (3.9 US qts, 3.3 Imp. qts) |
| Drain and refill without oil filter change | 3.4 liters (3.6 US qts, 3.0 Imp. qts) |
| Dry fill | 4.1 liters (4.3 US qts, 3.6 Imp. qts) |
| 62. INSPECT FOR ENGINE COOLANT LEAK |
![]() |
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
| *1 | Radiator Cap Tester |
Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 63. INSPECT ENGINE OIL LEVEL |
Warm up and stop the engine, and then wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.
If low, check for leakage and add oil up to the full level mark.
| 64. INSPECT FOR ENGINE OIL LEAK |
| 65. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check for fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts if necessary.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
| 66. INSPECT FOR EXHAUST GAS LEAK |
| 67. INSPECT IGNITION TIMING |
When using an intelligent tester:
Warm up and stop the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Select the following menu items:
Powertrain / Engine and ECT / Active Test / TC and TE1 / ON.
Inspect the ignition timing during idling.
| Transaxle | Ignition Timing |
| Manual Transaxle | 8 to 12 degrees BTDC |
| Automatic Transaxle |
Select the following menu items: TC and TE1 / OFF.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester:
Remove the No. 2 cylinder head cover .
![]() |
Pull out the wire harness (brown) shown in the illustration.
Warm up and stop the engine.
Connect the clip of the timing light to the wire harness.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Start the engine.
Inspect the ignition timing during idling.
| Transaxle | Ignition Timing |
| Manual Transaxle | 8 to 12 degrees BTDC |
| Automatic Transaxle |
Turn the ignition switch off.
Remove the timing light.
Install the No. 2 cylinder head cover .
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
| 68. INSPECT ENGINE IDLING SPEED |
When using an intelligent tester:
Warm up and stop the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Inspect the engine idling speed.
| Transaxle | Ignition Timing |
| Manual Transaxle | 600 to 700 rpm |
| Automatic Transaxle | 650 to 750 rpm |
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester.
Warm up and stop the engine.
![]() |
Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
| *a | Front view of DLC3 |
Start the engine.
Inspect the engine idling speed.
| Transaxle | Ignition Timing |
| Manual Transaxle | 600 to 700 rpm |
| Automatic Transaxle | 650 to 750 rpm |
Turn the ignition switch off.
Disconnect the tachometer.
Remove SST from terminal 9 (TAC).
| 69. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove the No. 2 cylinder head cover .
Remove the 4 ignition coils .
Remove the 4 spark plugs .
Disconnect the 4 fuel injector connectors.
![]() |
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs .
Install the 4 ignition coils .
Install the No. 2 cylinder head cover .
Clear the DTC (Click here).
| 70. INSPECT CO/HC |
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.
Check the CO/HC concentration during idling and when running at 2500 rpm.
Check the heated oxygen sensor operation (Click here).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idling (Black smoke from exhaust) |
|
| 71. INSTALL NO. 2 CYLINDER HEAD COVER |
Install the No. 2 cylinder head cover with the 4 nuts.
| 72. INSTALL ENGINE UNDER COVER LH (for Plastic Type) |
| 73. INSTALL ENGINE UNDER COVER RH (for Plastic Type) |
| 74. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type) |