Home › Drivetrain ยท CLUTCH › CLUTCH PEDAL (for RHD)

CLUTCH PEDAL (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL CLUTCH PEDAL PAD
  1. Install the clutch pedal pad to the clutch pedal sub-assembly.



2. INSTALL CLUTCH PEDAL STOPPER
  1. Install the clutch pedal stopper to the clutch pedal sub-assembly.



3. INSTALL NO. 1 CLUTCH PEDAL CUSHION
  1. Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.



4. INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH
  1. Install a new clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.

    HINT:
    Install the clutch master cylinder push rod clevis bush from the right side of the vehicle.



    C235134
  1. Apply MP grease to the inside of the clutch master cylinder push rod clevis bush.
    Text in Illustration 
    V100135
    MP grease



5. INSTALL CLUTCH PEDAL SHAFT COLLAR


    C235135
  1. Apply MP grease to both sides of 2 new clutch pedal bushes.
    Text in Illustration 
    V100135
    MP grease

  1. Install the 2 clutch pedal bushes and the clutch pedal shaft collar to the clutch pedal sub-assembly.



6. INSTALL CLUTCH PEDAL SUB-ASSEMBLY
  1. Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and the nut.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    NOTICE:
    Turn the nut while holding the bolt.



7. INSTALL CLUTCH PEDAL SPRING
  1. Install the clutch pedal spring to the clutch pedal sub-assembly and the clutch pedal support sub-assembly.



8. INSTALL CLUTCH PEDAL STOPPER BOLT
  1. Install the clutch pedal stopper bolt to the clutch pedal support sub-assembly and temporarily tighten the lock nut.

    HINT:
    Tighten the lock nut to the specified torque when adjusting the clutch pedal.



9. INSTALL NO. 2 CLUTCH START SWITCH ASSEMBLY (w/ Cruise Control System)
  1. Install the No. 2 clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



10. INSTALL CLUTCH START SWITCH ASSEMBLY
  1. Install the clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



11. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY
  1. Install the clutch pedal support sub-assembly to the vehicle with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the 2 bolts to the clutch pedal support sub-assembly.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 ft.*lbf }



    C245271
  1. Apply MP grease to the clevis pin.
    Text in Illustration 
    V100135
    MP grease

  1. Install the clutch master cylinder push rod clevis to the clutch pedal sub-assembly with the clevis pin and a new clip.

    HINT:
    Install the clevis pin from the right side of the vehicle.

  1. Connect the connectors and engage the wire harness clamps.



    C242394E01
  1. With the clutch pedal fully depressed, check that the clearance shown in the illustration is as specified.
    Text in Illustration 
    *a
    Clearance
    V100135
    Fully depressed

    Standard clearance:
    2.5 to 5.5 mm (0.098 to 0.217 in.)



12. INSPECT AND ADJUST CLUTCH PEDAL
(Click here)


13. INSPECT NO. 2 CLUTCH START SWITCH ASSEMBLY (w/ Cruise Control System)


    C245183E01
  1. Without depressing the clutch pedal, check that the clearance shown in the illustration is as specified.
    Text in Illustration 
    *a
    Clearance

    Standard clearance:
    for 1NZ-FE:
    0.5 to 3.5 mm (0.020 to 0.138 in.)
    for 2NZ-FE:
    2.5 to 5.5 mm (0.098 to 0.217 in.)



14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)
  1. for LHD:

    1. Engage the 5 claws and 2 clips and install the instrument panel finish panel.

  1. for RHD:

    1. Engage the 6 claws and 2 clips and install the instrument panel finish panel.



15. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

HINT:
Use the same procedure as for LHD models .



16. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

HINT:
Use the same procedure as for LHD models .



17. INSPECT CLUTCH START SYSTEM
  1. Check that the engine does not start when the clutch pedal is released.

  1. Check that the engine starts when the clutch pedal is fully depressed.
    If necessary, replace the clutch start switch assembly.