Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY (for 3 Door)

REAR SEAT OUTER BELT ASSEMBLY (for 3 Door) > INSTALLATION

for Preparation Click here


HINT:
The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.



1. INSTALL SEAT BELT HOLE SEAL
  1. Engage the 2 claws to install the seat belt hole seal.



2. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY


    B108365E01
  1. Check the angle of inclination required to lock the retractor.
    Text in Illustration 
    *a
    Lock
    *b
    Unlock

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear seat 3 point type outer belt assembly.

  1. Engage the 2 hooks to install the rear seat 3 point type outer belt assembly.

  1. Install the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }

  1. Install the shoulder anchor with the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }

  1. Engage the 2 claws and install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the rear seat 3 point type outer belt assembly installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.

      NOTICE:
      If the operation is not as specified, replace the rear seat 3 point type outer belt assembly.

  1. Remove the bolt and disconnect the floor anchor part of the rear seat 3 point type belt assembly.



3. INSTALL ROOF SIDE INNER GARNISH
  1. Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish.

  1. Engage the 5 clips and install the roof side inner garnish.



4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 3 clips and the 3 claws and install the deck trim side panel.

  1. Install the 3 screws.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

HINT:
Use the same procedure as for the RH side.



6. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
  1. Engage the 2 claws and install the rear seat 3 point type outer belt.

  1. Tighten the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }



7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY
  1. Engage the 8 clips and the 10 claws.

  1. Engage the 3 guides and install the quarter trim panel.



8. INSTALL FRONT SEAT BELT OUTER BAR SUB-ASSEMBLY
  1. Connect the floor anchor part of the front seat outer belt assembly and install the front seat belt outer bar sub-assembly with the 2 bolts.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }



9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    B284341E01
  1. Align the paint mark on the front door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Flange Position

    Paint Mark:
    Area
    Color
    RH Side
    Yellow
    LH Side
    White

    NOTICE:
    After installation, check that the corners fit correctly.



10. INSTALL FRONT DOOR SCUFF PLATE
  1. Engage the 8 claws and install the front door scuff plate.



11. INSTALL REAR FLOOR FINISH PLATE


    B272624
  1. Disengage the 4 claws and 4 guides and remove the rear floor finish plate.



12. INSTALL JACK HANDLE (for RH Side)


13. INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
  1. Connect the connector.



    E222046
  1. Engage the claw to install the No. 2 room light assembly.



14. INSTALL SPARE WHEEL COVER
  1. Install the spare wheel cover.



15. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board.



16. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)



17. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


18. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)