Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD)

BRAKE BOOSTER (for LHD) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE BOOSTER ASSEMBLY
  1. Install a new gasket onto the brake booster assembly.

  1. Temporarily install the brake booster assembly with the 4 nuts.



    C241860E01
  1. Tighten the 4 nuts in the order shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the vacuum hose to the vacuum check valve with the clip.



2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C236725E02
  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly and provisionally install them with the bolt.
    Text in Illustration 
    *a
    Matchmark
    *b
    Front of the Vehicle

  1. Tighten the bolt B while aligning the No. 2 steering intermediate shaft assembly with the position C as shown in the illustration.

    Standard C:
    18.5 to 19.7 mm

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



3. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Install the push rod lock nut and brake master cylinder push rod clevis to the brake booster assembly.

    HINT:
    Tighten the push rod lock nut after adjusting the brake pedal height.



    C235059E01
  1. Apply lithium soap base glycol grease to the push rod pin.
    Text in Illustration 
    *1
    Lithium Soap Base Glycol Grease

  1. Install the brake master cylinder push rod clevis with the push rod pin and a new clip.

  1. Install the brake pedal return spring.



4. INSTALL OUTER COWL TOP PANEL
  1. Install the outer cowl top panel with the 8 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.



5. INSTALL INNER COWL TOP TO COWL BRACE
  1. Install the cowl top to cowl brace with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



6. INSTALL FRONT NO. 1 VENTILATOR SEAL
  1. Engage the clip and install the front No. 1 ventilator seal.



7. INSTALL FRONT AIR SHUTTER SEAL RH

HINT:
Use the same procedure for the RH and LH sides.



8. INSTALL PROPORTIONING VALVE ASSEMBLY (w/o ABS)
(Click here)


9. INSTALL BRAKE ACTUATOR ASSEMBLY (w/ ABS)
(Click here)


10. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
(Click here)


11. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
(Click here)


12. INSPECT AND ADJUST BRAKE PEDAL HEIGHT
(Click here)


13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
  1. for LHD:

    1. Engage the 5 claws and 2 clips and install the instrument panel finish panel.

  1. for RHD:

    1. Engage the 6 claws and 2 clips and install the instrument panel finish panel.



14. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
  1. Engage the 2 claws and 5 clips and install the instrument panel finish panel.



15. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Engage the guide and the claw.

  1. Install the instrument panel under cover with the 2 <A> screws.