DTC B1820/55 Short in Side Squib RH Circuit |
DTC B1821/55 Open in Side Squib RH Circuit |
DTC B1822/55 Short to GND in Side Squib RH Circuit |
DTC B1823/55 Short to B+ in Side Squib RH Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1820/55 |
|
|
| B1821/55 |
| |
| B1822/55 |
| |
| B1823/55 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the front seat side airbag assembly RH and airbag sensor assembly.
Disconnect the connectors from the front seat side airbag assembly RH and airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.
| *1 | Front Seat Side Airbag Assembly RH (Side Squib RH) |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (SIDE SQUIB RH) |
![]() |
Connect the connector to the airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Seat Side Airbag Assembly RH (Side Squib RH) |
| *2 | Airbag Sensor Assembly |
| *3 | Connector C |
| *a | Front view of wire harness connector (to Front Seat Side Airbag Assembly RH (Side Squib RH)) |
|
| ||||
| OK | ||
| ||
| 3.CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector C.
Disconnect the floor wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K30-1 (SFR+) - Body ground | Ignition switch ON | Below 1 V |
| K30-2 (SFR-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K30-1 (SFR+) - K30-2 (SFR-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K30-1 (SFR+) - Body ground | Always | 1 MΩ or higher |
| K30-2 (SFR-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K30-1 (SFR+) - K30-2 (SFR-) | Always | 1 MΩ or higher |
| *1 | Front Seat Side Airbag Assembly RH (Side Squib RH) |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Front Seat Side Airbag Assembly RH (Side Squib RH)) |
|
| ||||
| OK | |
| 4.CHECK DTC |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front seat side airbag assembly RH and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||