Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor)

CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor) > TERMINALS OF ECU

for Preparation Click here


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR (for LHD)


    E217688E07


    Text in Illustration 
    *a
    to ECM
    *b
    to Skid Control ECU (Brake Actuator Assembly)
    *c
    to Main Body ECU (Multiplex Network Body ECU)
    *d
    to Power Steering ECU Assembly
    *e
    to DLC3
    *f
    to No. 2 Junction Connector

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    A61-9 (CANH)
    L
    ECM
    A61-20 (CANL)
    W
    A61-10 (CANH)
    G
    to Skid Control ECU (Brake Actuator Assembly)
    A61-21 (CANL)
    W
    F82-1 (CANH)
    R
    Main Body ECU (Multiplex Network Body ECU)
    F82-12 (CANL)
    W
    F82-2 (CANH)
    LG
    Power Steering ECU Assembly
    F82-13 (CANL)
    W
    F82-3 (CANH)
    GR
    DLC3
    F82-14 (CANL)
    W
    F82-4 (CANH)
    SB
    No. 2 Junction Connector
    F82-15 (CANL)
    W



  2. NO. 1 JUNCTION CONNECTOR (for RHD)


    E217688E08


    Text in Illustration 
    *a
    to ECM
    *b
    to Skid Control ECU (Brake Actuator Assembly)
    *c
    to Main Body ECU (Multiplex Network Body ECU)
    *d
    to No. 2 Junction Connector

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    A61-9 (CANH)
    L
    ECM
    A61-20 (CANL)
    W
    A61-10 (CANH)
    G
    to Skid Control ECU (Brake Actuator Assembly)
    A61-21 (CANL)
    W
    F82-1 (CANH)
    R
    Main Body ECU (Multiplex Network Body ECU)
    F82-12 (CANL)
    W
    F82-4 (CANH)
    SB
    No. 2 Junction Connector
    F82-15 (CANL)
    W



  3. NO. 2 JUNCTION CONNECTOR (for LHD)


    E217689E04


    Text in Illustration 
    *a
    to Airbag Sensor Assembly
    *b
    to Combination Meter Assembly
    *c
    to Air Conditioning Amplifier Assembly*1
    *d
    to No. 1 Junction Connector

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    F83-4 (CANH)
    B
    Airbag Sensor Assembly
    F83-15 (CANL)
    W
    F83-7 (CANH)
    G
    Combination Meter Assembly
    F83-18 (CANL)
    W
    F83-8 (CANH)
    V
    Air Conditioning Amplifier Assembly*2
    F83-19 (CANL)
    W
    F83-10 (CANH)
    SB
    No. 1 Junction Connector
    F83-21 (CANL)
    W
    1. *1: w/ Cooler



  4. NO. 2 JUNCTION CONNECTOR (for RHD)


    E217689E05


    Text in Illustration 
    *a
    to Steering Angle Sensor (Spiral Cable Sub-assembly)*1
    *b
    to Airbag Sensor Assembly
    *c
    to Power Steering ECU Assembly
    *d
    to Combination Meter Assembly
    *e
    to Air Conditioning Amplifier Assembly*2
    *f
    to No. 1 Junction Connector
    *g
    to DLC3
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    F83-1 (CANH)
    P
    Steering Angle Sensor (Spiral Cable Sub-assembly)*1
    F83-12 (CANL)
    W
    F83-4 (CANH)
    B
    Airbag Sensor Assembly
    F83-15 (CANL)
    W
    F83-6 (CANH)
    LG
    Power Steering ECU Assembly
    F83-17 (CANL)
    W
    F83-7 (CANH)
    G
    Combination Meter Assembly
    F83-18 (CANL)
    W
    F83-8 (CANH)
    V
    Air Conditioning Amplifier Assembly*2
    F83-19 (CANL)
    W
    F83-10 (CANH)
    SB
    No. 1 Junction Connector
    F83-21 (CANL)
    W
    F83-11 (CANH)
    GR
    DLC3
    F83-22 (CANL)
    W
    1. *1: w/ VSC
    2. *2: w/ Cooler


CHECK DLC3

C188081E12

  1. Turn the ignition switch off.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F4-6 (CANH) - F4-14 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    F4-6 (CANH) - F4-16 (BAT)
    GR - BE
    Ignition switch off
    6 kΩ or higher
    F4-14 (CANL) - F4-16 (BAT)
    W - BE
    Ignition switch off
    6 kΩ or higher
    F4-6 (CANH) - F4-4 (CG)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    F4-14 (CANL) - F4-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK ECM

A258723E02

  1. Disconnect the A74 and B84 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A74-41 (CANH) - A74-49 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A74-41 (CANH) - A74-2 (+B)
    L - B
    Ignition switch off
    6 kΩ or higher
    A74-49 (CANL) - A74-2 (+B)
    W - B
    Ignition switch off
    6 kΩ or higher
    A74-41 (CANH) - B84-104 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    A74-49 (CANL) - B84-104 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

E217205E03


Text in Illustration 
*A
for LHD
*B
for RHD
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Multiplex Network Body ECU)
  1. Disconnect the F76 main body ECU (multiplex network body ECU) connector.

  2. Disconnect the 3B and 3C instrument panel junction block assembly connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F76-14 (CANH) - F76-13 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    F76-14 (CANH) - 3C-21
    R - L
    Ignition switch off
    6 kΩ or higher
    F76-13 (CANL) - 3C-21
    W - L
    Ignition switch off
    6 kΩ or higher
    F76-14 (CANH) - 3B-8
    R - W-B
    Ignition switch off
    200 Ω or higher
    F76-13 (CANL) - 3B-8
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK COMBINATION METER ASSEMBLY

E217699E01

  1. Disconnect the F1 combination meter assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F1-32 (CANH) - F1-31 (CANL)
    G - W
    Ignition switch off
    108 to 132 Ω
    F1-32 (CANH) - F1-40 (B)
    G - L
    Ignition switch off
    6 kΩ or higher
    F1-31 (CANL) - F1-40 (B)
    W - L
    Ignition switch off
    6 kΩ or higher
    F1-32 (CANH) - F1-21 (ET)
    G - W-B
    Ignition switch off
    200 Ω or higher
    F1-31 (CANL) - F1-21 (ET)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

E186733E06


Text in Illustration 
*A
w/ VSC
*B
w/o VSC
  1. Disconnect the A54*1 or A55*2 skid control ECU (brake actuator assembly) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A54-25 (CANH) - A54-14 (CANL)*1
    A55-25 (CANH) - A55-14 (CANL)*2
    G - W
    Ignition switch off
    54 to 69 Ω
    A54-25 (CANH) - A54-12 (+BS)*1
    A55-25 (CANH) - A55-12 (+BS)*2
    G - W
    Ignition switch off
    6 kΩ or higher
    A54-14 (CANL) - A54-12 (+BS)*1
    A55-14 (CANL) - A55-12 (+BS)*2
    W - W
    Ignition switch off
    6 kΩ or higher
    A54-25 (CANH) - A54-1 (GND1)*1
    A55-25 (CANH) - A55-1 (GND1)*2
    G - W-B
    Ignition switch off
    200 Ω or higher
    A54-14 (CANL) - A54-1 (GND1)*1
    A55-14 (CANL) - A55-1 (GND1)*2
    W - W-B
    Ignition switch off
    200 Ω or higher
    *1: w/ VSC
    *2: w/o VSC


CHECK AIRBAG SENSOR ASSEMBLY

E221476E01


Text in Illustration 
*A
w/o VSC
*B
w/ VSC
  1. Disconnect the F16 airbag sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F16-13 (CANH) - F16-22 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    F16-13 (CANH) - F4-16 (BAT)
    B - BE
    Ignition switch off
    6 kΩ or higher
    F16-22 (CANL) - F4-16 (BAT)
    W - BE
    Ignition switch off
    6 kΩ or higher
    F16-13 (CANH) - F4-4 (CG)
    B - W-B
    Ignition switch off
    200 Ω or higher
    F16-22 (CANL) - F4-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (w/ VSC)

E186735E02

  1. Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F30-4 (CANH) - F30-3 (CANL)
    P - W
    Ignition switch off
    54 to 69 Ω
    F30-4 (CANH) - F30-6 (BAT)
    P - SB
    Ignition switch off
    6 kΩ or higher
    F30-3 (CANL) - F30-6 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher
    F30-4 (CANH) - F30-2 (ESS)
    P - BR
    Ignition switch off
    200 Ω or higher
    F30-3 (CANL) - F30-2 (ESS)
    W - BR
    Ignition switch off
    200 Ω or higher


CHECK POWER STEERING ECU ASSEMBLY

C231648E01

  1. Disconnect the A42 and F6 power steering ECU assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F6-7 (CANH) - F6-8 (CANL)
    LG - W
    Ignition switch off
    54 to 69 Ω
    F6-7 (CANH) - A42-1 (PIG)
    LG - W
    Ignition switch off
    6 kΩ or higher
    F6-8 (CANL) - A42-1 (PIG)
    W - W
    Ignition switch off
    6 kΩ or higher
    F6-7 (CANH) - A42-2 (PGND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    F6-8 (CANL) - A42-2 (PGND)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Cooler)

E221478E01


Text in Illustration 
*A
for Automatic Air Conditioning System
*B
for Manual Air Conditioning System (w/ Cooler)
  1. Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F42-11 (TX+) - F42-12 (TX-)*1
    F41-8 (TX+) - F41-9 (TX-)*2
    V - W
    Ignition switch off
    54 to 69 Ω
    F42-11 (TX+) - F42-21 (B)*1
    F41-8 (TX+) - F4-16 (BAT)*2
    V - BE
    Ignition switch off
    6 kΩ or higher
    F42-12 (TX-) - F42-21 (B)*1
    F41-9 (TX-) - F4-16 (BAT)*2
    W - BE
    Ignition switch off
    6 kΩ or higher
    F42-11 (TX+) - F42-14 (GND)*1
    F41-8 (TX+) - F41-23 (GND)*2
    V - W-B
    Ignition switch off
    200 Ω or higher
    F42-12 (TX-) - F42-14 (GND)*1
    F41-9 (TX-) - F41-23 (GND)*2
    W - W-B
    Ignition switch off
    200 Ω or higher

    1. *1: for Automatic Air Conditioning System
    2. *2: for Manual Air Conditioning System (w/ Cooler)