DTC B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1623/81 |
|
|

| 1.CHECK HISTORY DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for history DTCs (Click here).
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.
Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (OPEN) |
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

| *1 | Side Airbag Sensor Assembly RH | *2 | Airbag Sensor Assembly |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) | *b | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-4 (BBR+) - K22-3 (BBR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-4 (BBR+) - K22-3 (BBR-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K22-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| K22-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| K22-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (OPEN) |
Using the service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

| *1 | No. 2 Side Airbag Sensor Assembly RH | *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) | *b | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-1 (BCR+) - K22-2 (BCR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-1 (BCR+) - K22-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 9.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K22-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| K22-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 10.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| K22-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1623/81 is output. | A |
| DTC B1628/82 is output. | B |
| DTC B1623/81 or B1628/82 is not output. | C |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable to the negative (-) battery terminal.
Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | |
| 12.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1623/81 or B1628/82 is not output. | A |
| DTC B1623/81 is output. | B |
| DTC B1628/82 is output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||