Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Separate Type Yaw Rate Sensor)

DTC    B1623/81    Side Airbag Sensor Assembly RH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.
The side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
This DTC is stored when a malfunction is detected for the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

DTC No.
DTC Detection Condition
Trouble Area
B1623/81
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).
  2. Side airbag sensor assembly RH malfunction
  3. No. 2 side airbag sensor assembly RH malfunction
  4. Airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor assembly RH
  3. No. 2 side airbag sensor assembly RH
  4. Airbag sensor assembly

WIRING DIAGRAM


C241675E14


INSPECTION PROCEDURE

1.CHECK HISTORY DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for history DTCs (Click here).

    Result:
    History DTC B1622/81 or B1632/81 is not output.

    HINT:
    Codes other than history DTCs B1622/81 and B1632/81 may be output at this time, but they are not related to this check.



NG
INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC (Click here)
OK


2.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (OPEN)


  1. Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.


    C249131E02


Text in Illustration 
*1
Side Airbag Sensor Assembly RH
*2
Airbag Sensor Assembly
*3
Floor Wire
*4
Connector B
*5
Connector C
*6
Service Wire
*a
Front view of wire harness connector
(to Airbag Sensor Assembly)
*b
Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K22-4 (BBR+) - K22-3 (BBR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT)


    C240717E01
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K22-4 (BBR+) - K22-3 (BBR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO B+)


    C240717E01
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K22-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    K22-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT TO GROUND)


    C240717E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K22-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    K22-3 (BBR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


7.CHECK FLOOR WIRE (OPEN)


  1. Using the service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.


    C239812E11


    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *4
    Connector B
    *5
    Connector C
    *6
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to No. 2 Side Airbag Sensor Assembly RH)

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K22-1 (BCR+) - K22-2 (BCR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


8.CHECK FLOOR WIRE (SHORT)


    C240718E01
  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K22-1 (BCR+) - K22-2 (BCR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


9.CHECK FLOOR WIRE (SHORT TO B+)


    C240718E01
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K22-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    K22-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


10.CHECK FLOOR WIRE (SHORT TO GROUND)


    C240718E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K22-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    K22-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C235513E01
  1. Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.

  1. Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1623/81 is output.
    A
    DTC B1628/82 is output.
    B
    DTC B1623/81 or B1628/82 is not output.
    C
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly

    HINT:
    Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable to the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


12.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH


    C166174E16
  1. Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1623/81 or B1628/82 is not output.
    A
    DTC B1623/81 is output.
    B
    DTC B1628/82 is output.
    C
    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly RH

    HINT:
    Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)