Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate

for Preparation Click here


DESCRIPTION

When the rear window defogger switch is turned on, a rear window defogger activation request signal is transmitted from the air conditioning control assembly to the air conditioning amplifier assembly. Upon receipt of the signal, the air conditioning amplifier assembly turns on the DEF relay to activate the rear window defogger system.

WIRING DIAGRAM


B291806E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    DEF relay
    OFF or ON
    -

    OK:
    The window defogger system operates normally.



NG
Go to step 2
OK

GO TO AIR CONDITIONING SYSTEM (Click here)  

2.INSPECT DEF RELAY
  1. Inspect the DEF relay (Click here).



NG
REPLACE DEF RELAY
OK


3.CHECK HARNESS AND CONNECTOR (DEF RELAY - IG1 NO. 1 RELAY AND BATTERY)


    B291807E01
  1. Remove the DEF relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DEF-1 - Body ground
    Ignition switch ON
    11 to 14 V
    DEF-5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    DEF Relay Holder



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (DEF RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Remove the DEF relay from the engine room relay block.

  1. Disconnect the F42 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DEF-2 - F42-38 (RDFG)
    Always
    Below 1 Ω
    DEF-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Reconnect the F42 air conditioning amplifier assembly connector.

  1. Reinstall the DEF relay.



    E233188E01
  1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F42-38 (RDFG) - F42-14 (GND)
    Ignition switch ON
    Rear window defogger switch ON
    Below 1 V
    F42-38 (RDFG) - F42-14 (GND)
    Ignition switch ON
    Rear window defogger switch OFF
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (REAR WINDOW DEFOGGER) - DEF RELAY AND BODY GROUND)
  1. Disconnect the O3 and Q1 back door glass (rear window defogger) connectors.

  1. Remove the DEF relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O3-1 (B) - DEF-3
    Always
    Below 1 Ω
    Q1-1 (E) - Body ground
    Always
    Below 1 Ω
    O3-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR GLASS (REAR WINDOW DEFOGGER)