Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

Using this circuit, the radio receiver assembly sends power to the amplifier microphone assembly, and the amplifier microphone assembly sends microphone signals to the radio receiver assembly

WIRING DIAGRAM


E226275E03


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)
  1. Disconnect the F47 radio receiver assembly connector.

  1. Disconnect the F95 amplifier microphone assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F47-6 (SNS2) - F95-4 (SNS2)
    Always
    Below 1 Ω
    F47-4 (MACC) - F95-1 (MACC)
    Always
    Below 1 Ω
    F47-5 (MIN+) - F95-2 (MCO+)
    Always
    Below 1 Ω
    F47-19 (MIN-) - F95-3 (MCO-)
    Always
    Below 1 Ω
    F47-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    F47-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    F47-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    F47-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    F47-18 (SGND) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the amplifier microphone assembly connector.

  1. Reconnect the radio receiver assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO RECEIVER ASSEMBLY


    E176671E67
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F47-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F47-18 (SGND) - Body ground
    Always
    Below 1 Ω
    F47-19 (MIN-) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Component with harness connected
(Radio Receiver Assembly)


NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY


    E228890E01
  1. Remove the amplifier microphone assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (SNS2) - 3 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Amplifier Microphone Assembly)



NG
REPLACE AMPLIFIER MICROPHONE ASSEMBLY (Click here)
OK


4.CHECK AMPLIFIER MICROPHONE ASSEMBLY


    E232312E03
  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 2 (MCO+) and 3 (MCO-).

  1. Check the waveform of the amplifier microphone assembly using the oscilloscope.
    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is output
    A
    A waveform synchronized with the voice input to the map light assembly is not output
    B

Text in Illustration 
*a
Component with harness connected
(Amplifier Microphone Assembly)


B
REPLACE AMPLIFIER MICROPHONE ASSEMBLY (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)