Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1500    Fuel Sender Open Detected

for Preparation Click here


DESCRIPTION

This DTC is output when the combination meter assembly detects a fuel sender gauge malfunction.

DTC No.
DTC Detection Condition
Trouble Area
B1500
When combination meter detects fuel sender gauge malfunction
  1. Harness or connector
  2. Combination meter assembly
  3. Fuel suction with pump and gauge tube assembly
  4. Fuel sender gauge assembly

WIRING DIAGRAM


E219770E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter 
    Tester Display
    Test part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel gauge
    EMPTY / 1/2 / FULL
    Vehicle is stopped and the engine idling

    OK:
    Fuel receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel sender gauge input/
    Min.: 0
    Max.: 127.5
    Fuel sender input value
    Unit: Liter

    OK:
    Fuel value displayed on the tester is approximately the same as needle indication.



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

3.INSPECT FUEL SENDER GAUGE ASSEMBLY


  1. Remove the fuel sender gauge assembly.

    1. for 2NZ-FE (Click here)
    2. for 1NZ-FE (Click here)

    E226985E01


Text in Illustration 
*a
Component without harness connected
(Fuel Sender Gauge Assembly)
-
-
  1. Check that the float moves smoothly between F and E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Float Level
    Float Position (mm (in.))
    Specified Condition
    1 - 2
    F
    142 to 152 (5.591 to 5.984)
    12.0 to 18.0 Ω
    1/2
    71.1 to 76.1 (2.799 to 2.996)
    208.3 Ω
    Warning
    5.9 to 10.9 (0.232 to 0.429)
    365.2 Ω
    E
    0 (0)
    405.0 to 415.0 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1NZ-FE)
    B
    NG (for 2NZ-FE)
    C

  1. Reinstall the fuel sender gauge assembly.



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A


4.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    E158805E09
  1. Remove the fuel suction with pump and gauge tube assembly.

    1. for 2NZ-FE (Click here)
    2. for 1NZ-FE (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Fuel Suction with Pump and Gauge Tube Assembly)
    *b
    Connector A
    *c
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1NZ-FE)
    B
    NG (for 2NZ-FE)
    C

  1. Reinstall the fuel suction with pump and gauge tube assembly.



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

C
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
A


5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
  1. Disconnect the F1 combination meter assembly connector.

  1. Disconnect the K17 fuel suction with pump and gauge tube assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-16 (L) - K17-2 (FS)
    Always
    Below 1 Ω
    F1-16 (L) - Body ground
    Always
    10 kΩ or higher
    K17-3 (FE) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the fuel suction with pump and gauge tube assembly connector.

  1. Reconnect the combination meter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)