Home › Engine / Hybrid System ยท 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

  1. For w/o ABS models.
The vehicle speed is detected using the speedometer sensor. The speedometer sensor transmits a 4- pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A112641E05

  1. For w/ ABS models.
Vehicles that are equipped with ABS (Anti-lock Brake System) detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4- pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A079413E42


DTC No.
DTC Detection Condition
Trouble Area
P0500
While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM.
(1 trip detection logic: Automatic transaxle)
(2 trip detection logic: Manual transaxle)
  1. Open or short in speed signal circuit
  2. Combination meter assembly
  3. Brake actuator assembly (Skid control ECU)*1
  4. Speedometer sensor*2
  5. ECM
  1. *1: w/ ABS models
  2. *2: w/o ABS models

HINT:
  1. Various systems use the vehicle speed signal distributed from the combination meter. Check all the components possibly related to speed signal.
  2. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
  3. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.


MONITOR DESCRIPTION

  1. Automatic Transaxle Models
    The ECM assumes that the vehicle is being driven when the indicated engine speed is more than 2000 rpm and 30 seconds have elapsed since the Park/Neutral Position (PNP) switch was turned off (typical example value). If there is no speed signal from the combination meter, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.
  1. Manual Transaxle Models
    The ECM assumes that the vehicle is being driven when fuel cut with the accelerator pedal released continues for 5 seconds or more. If there is no speed signal from the combination meter, despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
Vehicle speed sensor, Combination meter and Skid control ECU
Required Sensors/Components (Related)
Park/neutral position switch assembly, Engine coolant temperature sensor, Throttle with motor body assembly and Mass air flow meter
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


A/T: 
Ignition Switch
ON
Time after ignition switch OFF to ON
3 seconds or more
Battery voltage
11 V or higher
Starter
OFF
Time after PNP switch turned off
30 seconds

M/T: 
Time after ignition switch turned from OFF to ON
3 seconds or more
Ignition switch
ON
Starter
OFF
Fuel-cut
ON

TYPICAL MALFUNCTION THRESHOLDS


Vehicle speed sensor signal
No pulse input

CONFIRMATION DRIVING PATTERN


A240416E04

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine.
  7. Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].
  9. Stop the vehicle.
  10. Enter the following menus: Powertrain / Engine and ECT / DTC [D].
  11. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P0500.
  14. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.


WIRING DIAGRAM


A254089E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    Result 
    Result
    Proceed to
    Values displayed on tester and speedometer display not equal
    A
    Values displayed on tester and speedometer display equal
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK COMBINATION METER SYSTEM
  1. Check the circuits that send vehicle speed signals to this system in the meter system (Click here).


NEXT


3.CHECK WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

    HINT:
    If no DTCs (no pending DTCs) are output to the tester, the repair has been successfully completed.


NEXT

END