Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > Engine does not Start because No Initial Combustion

for Preparation Click here


DESCRIPTION

  1. When the key is inserted into the ignition key cylinder, the antenna coil receives the key code. Then the amplifier amplifies the ID code and outputs it to the transponder key ECU assembly.
  2. If this symptom occurs, there may be a communication problem between the transponder key amplifier and the transponder key ECU assembly.

WIRING DIAGRAM


B291391E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.
  2. Inspection the fuses for circuits related to this system before performing the following inspection procedure.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    Result 
    Result
    Proceed to
    No DTC output
    A
    DTC output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser Fuel Cut
    Status of immobiliser fuel cut/
    OFF or ON
    -
    -

    OK:
    The item in the Data List indicates "OFF"

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 2NZ-FE)
    B
    OK (for 1NZ-FE)
    C



B
GO TO SFI SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)
A


4.CHECK THEFT WARNING INDICATOR LIGHT OPERATION
  1. When the key inserted in ignition key cylinder, check that the theft warning indicator light assembly off.

    OK:
    The theft warning indicator light assembly off.



NG
Go to step 5
OK

GO TO ENGINE DOES NOT START BUT INITIAL COMBUSTION OCCURS (Click here)  

5.CHECK THEFT WARNING INDICATOR LIGHT OPERATION
  1. Perform inspection using a different key that has been registered to the vehicle.

  1. When the key inserted in ignition key cylinder, check that the theft warning indicator light assembly off.

    OK:
    The theft warning indicator light assembly off.



NG
Go to step 7
OK


6.CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
  1. Perform inspection using a different key that has been registered to the vehicle.

  1. It leaves for 5 seconds by the ignition switch ON status, and the engine starting operation is done.
    Result 
    Result
    Proceed to
    Engine cannot be started
    A
    Engine can be started
    B



B
Go to step 19
A

GO TO ENGINE DOES NOT START BUT INITIAL COMBUSTION OCCURS (Click here)  

7.CHECK TRANSPONDER KEY AMPLIFIER (VC5 SIGNAL)
  1. Disconnect the F55 transponder key amplifier connector.



    B287949E04
  1. Using an oscilloscope, check the waveform.

    1. Waveform
      Measurement Condition 
      Item
      Content
      Tester Connection
      F55-1 (VC5) - Body ground
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

      OK:
      Waveform is output normally (refer to illustration).

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transponder Key Amplifier)
      *b
      Waveform



NG
Go to step 8
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY, IG TERMINAL VOLTAGE)
  1. Disconnect the F55 transponder key amplifier connector.

  1. Disconnect the F54 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F55-1 (VC5) - F54-14 (VC5)
    Always
    Below 1 Ω
    F55-7 (AGND) - F54-5 (AGND)
    Always
    Below 1 Ω
    F55-1 (VC5) - Body ground
    Always
    10 kΩ or higher



    B287750E02
  1. Reconnect the transponder key amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F54-2 (IG) - F54-16 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transponder Key ECU assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK TRANSPONDER KEY AMPLIFIER (TXCT SIGNAL)
  1. Disconnect the F55 transponder key amplifier connector.



    B287951E04
  1. Using an oscilloscope, check the waveform.

    1. Waveform
      Measurement Condition 
      Item
      Content
      Tester Connection
      F55-5 (TXCT) - Body ground
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

      OK:
      Waveform is output normally (refer to illustration).

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transponder Key Amplifier)
      *b
      Waveform



NG
Go to step 10
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

10.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
  1. Disconnect the F55 transponder key amplifier connector.

  1. Disconnect the F54 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F55-5 (TXCT) - F54-4 (TXCT)
    Always
    Below 1 Ω
    F55-5 (TXCT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK TRANSPONDER KEY AMPLIFIER (CODE SIGNAL)
  1. Disconnect the F55 transponder key amplifier connector.



    B287950E05
  1. Using an oscilloscope, check the waveform.

    1. Waveform
      Measurement Condition 
      Item
      Content
      Tester Connection
      F55-4 (CODE) - Body ground
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

      OK:
      Waveform is output normally (refer to illustration).

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transponder Key Amplifier)
      *b
      Waveform



NG
Go to step 12
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

12.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
  1. Disconnect the F55 transponder key amplifier connector.

  1. Disconnect the F54 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F55-4 (CODE) - F54-15 (CODE)
    Always
    Below 1 Ω
    F55-4 (CODE) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the transponder key ECU assembly connector.

  1. Reconnect the transponder key amplifier connector.



    B287950E06
  1. Using an oscilloscope, check the waveform.

    1. Waveform
      Measurement Condition 
      Item
      Content
      Tester Connection
      F55-4 (CODE) - Body ground
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

      OK:
      Waveform is output normally (refer to illustration).

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transponder Key Amplifier)
      *b
      Waveform
      Result 
      Result
      Proceed to
      Terminal CODE stuck high (5 V)
      A
      Terminal CODE stuck low (1 V or less)
      B
      Problem in wire harness or connector
      C



B
Go to step 15

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


13.REPLACE TRANSPONDER KEY AMPLIFIER
  1. Replace the transponder key amplifier (Click here).


NEXT


14.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts with an already registered vehicle key.

    OK:
    Engine starts normally.



NG
Go to step 15
OK

END (TRANSPONDER KEY AMPLIFIER WAS DEFECTIVE) 

15.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).


NEXT


16.REGISTER KEY
  1. Register the key (Refer to Service Bulletin).


NEXT


17.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID (Refer to Service Bulletin).


NEXT


18.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts with an already registered vehicle key.

    OK:
    Engine starts normally.



NG
Go to step 19
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE) 

19.REPLACE KEY
  1. Replace the transponder key master transmitter with a new one (Refer to Service Bulletin).


NEXT


20.REREGISTER KEY
  1. Reregister the key (Refer to Service Bulletin).


NEXT


21.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts with an already registered vehicle key.

    OK:
    Engine starts normally.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2NZ-FE)
    B
    NG (for 1NZ-FE)
    C



B
GO TO SFI SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)
A

END (KEY (TRANSPONDER KEY MASTER TRANSMITTER) WAS DEFECTIVE)