TRANSMISSION
A760E AUTOMATIC TRANSMISSION
ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM
- PRECAUTION
- DEFINITION OF TERMS
- PART AND SYSTEM NAME LIST
- PARTS LOCATION
- SYSTEM DIAGRAM
- SYSTEM DESCRIPTION
- HOW TO PROCEED WITH TROUBLESHOOTING
- ROAD TEST
- MECHANICAL SYSTEM TESTS
- HYDRAULIC TEST
- MANUAL SHIFTING TEST
- INITIALIZATION
- MONITOR DRIVE PATTERN
- PROBLEM SYMPTOMS TABLE
- TERMINALS OF ECM
- DIAGNOSIS SYSTEM
- DTC CHECK / CLEAR
- CHECK MODE PROCEDURE
- FAIL-SAFE CHART
- DATA LIST / ACTIVE TEST
- DIAGNOSTIC TROUBLE CODE CHART
- P0500 No speed sensor signal to ECM under following conditions: (1-trip detection logic)(a) Park/neutral position...
- P0781 1-2 shift valve malfunction: Shifting to 2nd and 4th gears is impossible. When the ECM directs the gearshift...
- P0705 (A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)P input signal is...
- P0973 ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip detection...
- P0710 (a) and (b) are detected momentary within 0.5 sec. when neither P0712 or P0713 is not detected (1-trip...
- P0974 ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip...
- P0712 ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic)
- P0976 ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip detection...
- P0713 ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more after the engine startDTC is...
- P0977 ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip...
- P0711 Both (a) and (b) are detected: (2-trip detection logic)Intake air and engine coolant temps. are more than...
- P0979 ECM detects short in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip detection...
- P0717 ECM detects conditions (a), (b) and (c) continuity for 5 sec. or more: (1-trip detection logic)Output shaft...
- P0980 ECM detects open in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip detection...
- P0724 The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO...
- P0982 ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1-trip detection...
- P0729 6th gearshift malfunction:The ECM determines there is a malfunction when both of the following conditions are...
- P0983 ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1-trip...
- P0748 The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0985 ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip detection...
- P0751 S1 stuck ON malfunction*1:The ECM determines there is a malfunction when the following conditions are both...
- P0986 ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1-trip...
- P0756 S2 stuck ON malfunction*1:Shifting to 3rd and 5th gears is impossible.The ECM determines there is a...
- P2714 ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the...
- P0761 S3 stuck ON malfunction*1:When the ECM directs the gearshift to switch to 5th or 6th gear, the engine...
- P2716 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip...
- P0766 "S4 stuck OFF malfunction", "SL2 stuck ON malfunction" or "Brake control valve malfunction"*1:Shifting to 5th...
- P2757 Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h [50 mph]), or lock-up...
- P0778 The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears....
- P2759 Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1-trip...
- Transmission Control Switch Circuit
- Pattern Select Switch Snow Mode Circuit
- Pattern Select Switch Power Mode Circuit
AUTOMATIC TRANSMISSION FLUID
EXTENSION HOUSING REAR OIL SEAL
SPEED SENSOR
TRANSMISSION WIRE
PARK / NEUTRAL POSITION SWITCH
VALVE BODY ASSEMBLY
SHIFT LOCK SYSTEM
FLOOR SHIFT ASSEMBLY
AUTOMATIC TRANSMISSION ASSEMBLY
TORQUE CONVERTER AND DRIVE PLATE
AUTOMATIC TRANSMISSION UNIT
OIL PUMP
CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
VALVE BODY
SHIFT SOLENOID VALVE
A761E AUTOMATIC TRANSMISSION
ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM
- PRECAUTION
- DEFINITION OF TERMS
- PART AND SYSTEM NAME LIST
- PARTS LOCATION
- SYSTEM DIAGRAM
- SYSTEM DESCRIPTION
- HOW TO PROCEED WITH TROUBLESHOOTING
- ROAD TEST
- MECHANICAL SYSTEM TESTS
- HYDRAULIC TEST
- MANUAL SHIFTING TEST
- INITIALIZATION
- MONITOR DRIVE PATTERN
- PROBLEM SYMPTOMS TABLE
- TERMINALS OF ECM
- DIAGNOSIS SYSTEM
- DTC CHECK / CLEAR
- CHECK MODE PROCEDURE
- FAIL-SAFE CHART
- DATA LIST / ACTIVE TEST
- DIAGNOSTIC TROUBLE CODE CHART
- P0500 No speed sensor signal to ECM under following conditions: (1-trip detection logic)(a) Park/neutral position...
- P0781 1-2 shift valve malfunction: Shifting to 2nd and 4th gears is impossible. When the ECM directs the gearshift...
- P0705 (A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)P input signal is...
- P0973 ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip detection...
- P0710 (a) and (b) are detected momentary within 0.5 sec. when neither P0712 or P0713 is not detected (1-trip...
- P0974 ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip...
- P0712 ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic)
- P0976 ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip detection...
- P0713 ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more after the engine startDTC is...
- P0977 ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip...
- P0711 Both (a) and (b) are detected: (2-trip detection logic)Intake air and engine coolant temps. are more than...
- P0979 ECM detects short in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip detection...
- P0717 ECM detects conditions (a), (b) and (c) continuity for 5 sec. or more: (1-trip detection logic)Output shaft...
- P0980 ECM detects open in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip detection...
- P0724 The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO...
- P0982 ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1-trip detection...
- P0729 6th gearshift malfunction:The ECM determines there is a malfunction when both of the following conditions are...
- P0983 ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1-trip...
- P0748 The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0985 ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip detection...
- P0751 S1 stuck ON malfunction*1:The ECM determines there is a malfunction when the following conditions are both...
- P0986 ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1-trip...
- P0756 S2 stuck ON malfunction*1:Shifting to 3rd and 5th gears is impossible.The ECM determines there is a...
- P2714 ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the...
- P0761 S3 stuck ON malfunction*1:When the ECM directs the gearshift to switch to 5th or 6th gear, the engine...
- P2716 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip...
- P0766 "S4 stuck OFF malfunction", "SL2 stuck ON malfunction" or "Brake control valve malfunction"*1:Shifting to 5th...
- P2757 Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h [50 mph]), or lock-up...
- P0778 The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears....
- P2759 Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1-trip...
- Transmission Control Switch Circuit
- Pattern Select Switch Snow Mode Circuit
- Pattern Select Switch Power Mode Circuit
- Kick Down Switch Circuit
AUTOMATIC TRANSMISSION FLUID
EXTENSION HOUSING REAR OIL SEAL
SPEED SENSOR
TRANSMISSION WIRE
PARK / NEUTRAL POSITION SWITCH
VALVE BODY ASSEMBLY
SHIFT LOCK SYSTEM
FLOOR SHIFT ASSEMBLY
AUTOMATIC TRANSMISSION ASSEMBLY
TORQUE CONVERTER AND DRIVE PLATE
AUTOMATIC TRANSMISSION UNIT
OIL PUMP
CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
VALVE BODY
SHIFT SOLENOID VALVE
A960E AUTOMATIC TRANSMISSION
ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM
- PRECAUTION
- DEFINITION OF TERMS
- PART AND SYSTEM NAME LIST
- PARTS LOCATION
- SYSTEM DIAGRAM
- SYSTEM DESCRIPTION
- HOW TO PROCEED WITH TROUBLESHOOTING
- ROAD TEST
- MECHANICAL SYSTEM TESTS
- HYDRAULIC TEST
- MANUAL SHIFTING TEST
- INITIALIZATION
- MONITOR DRIVE PATTERN
- PROBLEM SYMPTOMS TABLE
- TERMINALS OF ECM
- DIAGNOSIS SYSTEM
- DTC CHECK / CLEAR
- CHECK MODE PROCEDURE
- FAIL-SAFE CHART
- DATA LIST / ACTIVE TEST
- DIAGNOSTIC TROUBLE CODE CHART
- P0500 No speed sensor signal to ECM under following conditions: (1-trip detection logic)(a) Park/neutral position...
- P0781 1-2 shift valve malfunction: Shifting to 2nd and 4th gears is impossible. When the ECM directs the gearshift...
- P0705 (A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)P input signal is...
- P0973 ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip detection...
- P0710 (a) and (b) are detected momentary within 0.5 sec. when neither P0712 or P0713 is not detected (1-trip...
- P0974 ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip...
- P0712 ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic)
- P0976 ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip detection...
- P0713 ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more after the engine startDTC is...
- P0977 ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip...
- P0711 Both (a) and (b) are detected: (2-trip detection logic)Intake air and engine coolant temps. are more than...
- P0979 ECM detects short in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip detection...
- P0717 ECM detects conditions (a), (b) and (c) continuity for 5 sec. or more: (1-trip detection logic)Output shaft...
- P0980 ECM detects open in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip detection...
- P0724 The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO...
- P0982 ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1-trip detection...
- P0729 6th gearshift malfunction:The ECM determines there is a malfunction when both of the following conditions are...
- P0983 ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1-trip...
- P0748 The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0985 ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip detection...
- P0751 S1 stuck ON malfunction*1:The ECM determines there is a malfunction when the following conditions are both...
- P0986 ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1-trip...
- P0756 S2 stuck ON malfunction*1:Shifting to 3rd and 5th gears is impossible.The ECM determines there is a...
- P2714 ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the...
- P0761 S3 stuck ON malfunction*1:When the ECM directs the gearshift to switch to 5th or 6th gear, the engine...
- P2716 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip...
- P0766 "S4 stuck OFF malfunction", "SL2 stuck ON malfunction" or "Brake control valve malfunction"*1:Shifting to 5th...
- P2757 Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h [50 mph]), or lock-up...
- P0778 The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears....
- P2759 Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1-trip...
- Transmission Control Switch Circuit
- Pattern Select Switch Snow Mode Circuit
- Pattern Select Switch Power Mode Circuit
- Kick Down Switch Circuit