| Last Modified: 11-27-2007 | 1.6 A | |
| Service Category: Vehicle Exterior | Section: Door/Hatch | |
| Model Year: 2008 | Model: LX570 | Doc ID: RM000001BLH00SX |
| Title: DOOR / HATCH: TAIL GATE: DISASSEMBLY (2008 LX570) | ||
DISASSEMBLY
1. REMOVE ENGINE ROOM SIDE COVER LH
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
-
w/ Navigation System:
After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.
-
When disconnecting the cable, some systems need to be initialized after the cable is reconnected
.
3. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE
4. REMOVE BACK DOOR TRIM COVER LH
|
(a) Remove the back door trim cover LH as shown in the illustration. |
5. REMOVE BACK DOOR TRIM COVER RH
|
(a) Remove the back door trim cover RH as shown in the illustration. |
6. REMOVE BACK DOOR TRIM PANEL ASSEMBLY
|
(a) Remove the 4 bolts. |
(b) Detach the 16 clips and remove the back door trim panel.
7. REMOVE REAR BUMPER COVER
(a) Remove the bumper cover
.
8. REMOVE SPARE TIRE
9. REMOVE LOWER BACK DOOR TORSION BAR ASSEMBLY
|
(a) Remove the 4 bolts and lower back door torsion bar. |
10. REMOVE BACK DOOR TORSION BAR GUIDE
|
(a) Detach the 2 claws and remove the back door torsion bar guide. |
11. REMOVE BACK DOOR INSIDE HANDLE ASSEMBLY
|
(a) Remove the screw and back door inside handle. |
12. REMOVE BACK DOOR GARNISH
|
(a) Detach the 4 clips and remove the back door garnish. |
13. REMOVE LOWER TAIL GATE LOCK ASSEMBLY RH
(a) w/o Power Back Door:
|
(1) Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock. |
|
(2) Disconnect the cable from the lower tail gate lock. |
(b) w/ Power Back Door:
|
(1) Disconnect the connector. |
|
(2) Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock. |
14. REMOVE BACK DOOR REMOTE CONTROL ASSEMBLY
(a) w/o Power Back Door:
|
(1) Remove the back door handle grommet. |
|
(2) Remove the 2 screws. |
|
(3) Disconnect the left side cable. |
(4) Remove the back door remote control.
(b) w/ Power Back Door:
|
(1) Disconnect the connector. |
(2) Remove the 2 screws and back door remote control.
|
(3) Remove the back door handle grommet. |
15. REMOVE LOWER TAIL GATE LOCK ASSEMBLY LH
(a) w/o Power Back Door:
|
(1) Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock. |
(b) w/ Power Back Door:
|
(1) Disconnect the connector. |
|
(2) Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock. |
16. REMOVE NO. 2 BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE
17. REMOVE TAIL GATE STAY SUB-ASSEMBLY LH
|
(a) Using a T40 "TORX" socket, remove the 2 screws and tail gate stay. |
18. REMOVE TAIL GATE STAY SUB-ASSEMBLY RH
HINT:
Use the same procedures described for the LH side.
19. REMOVE BACK DOOR DAMPER ASSEMBLY
|
(a) Remove the bolt and back door damper. |
|
|