Home › Drivetrain › Axle/Differential › AXLE AND DIFFERENTIAL: REAR AXLE SHAFT
Last Modified: 11-27-2007 1.6 A
Service Category: Drivetrain Section: Axle/Differential
Model Year: 2008 Model: LX570 Doc ID: RM00000270D00BX
Title: AXLE AND DIFFERENTIAL: REAR AXLE SHAFT: INSTALLATION (2008 LX570)

INSTALLATION

1. INSTALL REAR AXLE SHAFT OIL SEAL LH

(a) Using SST and a hammer, tap in a new oil seal.

NOTICE:

Do not allow foreign matter, etc. to contact the axle shaft housing hole.

SST: 09950-60020

09951-00770

SST: 09950-70010

09951-07150

2. INSTALL REAR AXLE SHAFT LH

(a) Install the O-ring to the axle housing.

(b) Install the rear axle shaft and parking brake plate with the 4 nuts.

Torque: 60 N·m (612 kgf·cm, 44 ft·lbf)

3. CONNECT REAR SPEED SENSOR LH BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: REAR SPEED SENSOR: INSTALLATION (2008 LX570)+

4. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY PARKING BRAKE: PARKING BRAKE ASSEMBLY: REASSEMBLY (2008 LX570)+

5. INSTALL PARKING BRAKE SHOE LEVER SUB-ASSEMBLY LH PARKING BRAKE: PARKING BRAKE ASSEMBLY: REASSEMBLY (2008 LX570)+

6. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH PARKING BRAKE: PARKING BRAKE ASSEMBLY: REASSEMBLY (2008 LX570)+

7. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH PARKING BRAKE: PARKING BRAKE ASSEMBLY: REASSEMBLY (2008 LX570)+

8. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING LH PARKING BRAKE: PARKING BRAKE ASSEMBLY: REASSEMBLY (2008 LX570)+

9. CHECK PARKING BRAKE INSTALLATION PARKING BRAKE: PARKING BRAKE ASSEMBLY: REASSEMBLY (2008 LX570)+

10. INSTALL REAR DISC LH BRAKE (REAR): REAR BRAKE: INSTALLATION (2008 LX570)+

11. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

(a) Connect the rear disc brake cylinder and install 2 new bolts.

Torque: 95 N·m (969 kgf·cm, 70 ft·lbf)

NOTICE:

  • Do not twist the flexible hose.
  • Make sure that the bolts are free from damage and foreign matter.
  • Do not overtighten the bolts.

12. CONNECT REAR BRAKE FLEXIBLE HOSE

(a) Set the flexible hose to the connecting point with the brake tube, and then install a new clip.

(b) Using union nut wrench, connect the flexible hose to the brake tube while holding the flexible hose with a wrench.

Torque: 15 N·m (155 kgf·cm, 11 ft·lbf)

Torque: 14 N·m (145 kgf·cm, 10 ft·lbf)

HINT:

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).

NOTICE:

  • Do not bend or damage the brake tube.
  • Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.

13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION (2008 LX570) .

14. FILL RESERVOIR WITH BRAKE FLUID BRAKE SYSTEM (OTHER): BRAKE FLUID: BLEEDING (2008 LX570)+

15. BLEED AIR FROM BRAKE LINE BRAKE SYSTEM (OTHER): BRAKE FLUID: BLEEDING (2008 LX570)+

16. CHECK BRAKE FLUID LEVEL IN RESERVOIR BRAKE SYSTEM (OTHER): BRAKE FLUID: ON-VEHICLE INSPECTION (2008 LX570)+

17. CHECK FOR BRAKE FLUID LEAK

18. INSPECT DIFFERENTIAL OIL AXLE AND DIFFERENTIAL: DIFFERENTIAL OIL: REPLACEMENT (2008 LX570)+

19. INSPECT FOR DIFFERENTIAL OIL LEAK

20. CHECK PARKING BRAKE LEVER TRAVEL PARKING BRAKE: PARKING BRAKE SYSTEM: ADJUSTMENT (2008 LX570)+

21. ADJUST PARKING BRAKE LEVER TRAVEL PARKING BRAKE: PARKING BRAKE SYSTEM: ADJUSTMENT (2008 LX570)+

22. CHECK SRS WARNING LIGHT

(a) Check the SRS warning light SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: DIAGNOSIS SYSTEM (2008 LX570) .

23. CHECK SPEED SENSOR SIGNAL

(a) Check the speed sensor signal BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: TEST MODE PROCEDURE (2008 LX570) .

24. INSTALL REAR WHEEL LH

Torque: 131 N·m (1336 kgf·cm, 97 ft·lbf)