[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
13 -FUEL > 13A-DIRECT INJECTION AND MULTIPOINT FUEL INJECTION (DI AND MPI) > TROUBLESHOOTING > DIAGNOSIS CODE PROCEDURES > CODE NO. P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED
Code No. P0300: Random/Multiple Cylinder Misfire Detected
 
 
 
 
FUNCTION
  • If a misfire occurs while the engine is running, the engine speed changes for an instant.
  • The engine-ECU checks for such changes in engine speed.
 
 
TROUBLE JUDGEMENT
Check Conditions
  • Engine speed is more than 440 r/min and is less than 4,500 r/min.
  • Engine coolant temperature is more than -10°C.
  • Barometric pressure is more than 76 kPa.
  • Volumetric efficiency is more than specified value that depend on engine speed.
  • Adaptive learning is complete for the vane which generates a crankshaft position signal.
  • While the engine is running, excluding gear shifting, deceleration, sudden acceleration/deceleration and A/C compressor switching.
  • The throttle deviation is -0.06 V/10 ms to +0.22 V/10 ms.
Judgement Criterion (change in the angular acceleration of the crankshaft is used for misfire detection).
  • Misfire has occurred more frequently than allowed during the last 200 revolutions (when the catalyst temperature is more than 1,000°C).
or
  • Misfire has occurred in 2.0 % or more of the last 1,000 revolutions (corresponding to 1.5 times the limit of emission standard).
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • The supply of fuel to the misfiring cylinder can possibly be cut.
 
 
PROBABLE CAUSES
  • Ignition system related part(s) failed
  • Failed crank angle sensor
  • Failed injector
  • Incorrect air-fuel ratio
  • Low compression pressure
  • Failed No. 1 intake air temperature sensor
  • Failed engine coolant temperature sensor
  • Failed air flow sensor
  • Skipping of timing chain teeth.
  • Failed engine-ECU
 
 
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III data list
  • Data list reference table (Refer to ).
  1. Item 2: Crank angle sensor
  2. Item 5: No. 1 intake air temperature sensor
  3. Item 6: Engine coolant temperature sensor
  4. Item 10: Air flow sensor
  5. Item 26: Long-term fuel trim
  6. Item 28: Short-term fuel trim
Are the check results normal?
YES : Go to Step 2.
Perform the diagnosis code classified check procedure for the sensor that has shown an abnormal data value. Inspection chart for diagnosis code (Refer to ).
 
STEP 2. Visual check of ignition spark.
  • Remove the spark plug and install it to the ignition coil.
  • Connect the ignition coil connector.
  • Disconnect all injector connectors.
  • At the engine start, check each spark plug produces a spark.
Is the check result normal?
Go to Step 3.
Check Inspection Procedure - ignition circuit system (Refer to ).
 
STEP 3. Check injector itself.
  • Injector check (Refer to ).
Is the check result normal?
Go to Step 4.
Replace the injector.
 
STEP 4. Check air intake from inlet hose and inlet manifold.
Is the check result normal?
Go to Step 5.
Repair.
 
STEP 5. Fuel pressure measurement.
  • Fuel pressure test (Refer to )
Is the check result normal?
Go to Step 6.
Repair.
 
STEP 6. Check for skipped timing chain teeth.
Is the check result normal?
Go to Step 7.
Replace the timing chain.
 
STEP 7. Check compression pressure.
  • Check the compression pressure (Refer to GROUP 11A - On-vehicle Service - Compression Pressure Check ).
Is the check result normal?
Go to Step 8.
Repair.
 
STEP 8. Replace the engine-ECU.
  • After replacing the engine-ECU, reconfirm whether the diagnosis code is set.
Is the diagnosis code set?
Check for foreign matters (water, diesel fuel, etc.) in fuel and replace if necessary.
Check end.