[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
52 -INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM(SRS) > 52B-SUPPLEMENTAL RESTRAINT SYSTEM (SRS) > TROUBLESHOOTING > DIAGNOSIS CODE PROCEDURES > DTC B1625 LAP PRE-TENSIONER SQUIB SHORT-CIRCUITED
Code No. B1625 Lap pre-tensioner (squib) system (short circuit between squib circuit terminals)
 
 
cautionIf the diagnosis code B1625 is set to SRS-ECU, be sure to diagnose the CAN bus line.
 
 
OPERATION
Only when the frontal collision impact that exceeds the threshold is simultaneously detected (turned ON) by the front impact sensor as well as by the analogue G-sensor and safing G-sensor in SRS-ECU, the electric current is supplied from SRS-ECU to the lap pre-tensioner (squib).
 
 
 
TROUBLE JUDGEMENT
The code is set when the short circuit occurs to between the terminals of SRS-ECU lap pre-tensioner (squib) circuit.
 
 
 
PROBABLE CAUSES
  • Damaged short spring *
  • Short circuit between terminals of lap pre-tensioner (squib) circuit
  • Damaged connector(s)
  • Malfunction of SRS-ECU
  • Insufficient press of locking button or locking button not pressed
note*: The squib circuit connectors integrate a short spring (which prevents the air bags from being unintentionally deployed because of static electricity by shorting the positive wire to the earth wire in the squib circuit when the connectors are disconnected). Therefore, when the above codes are set, the short spring may not be released due to the damaged connector even when the connectors are connected.
 
 
 
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-IIISE CAN bus diagnostics.
Use M.U.T.-IIISE to diagnose the CAN bus lines.
Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
 
STEP 2. Check whether the diagnosis code is set again.
(1) Connect the negative battery terminal.
(2) After erasing the diagnosis code memory, check the diagnosis code again.
(3) Disconnect the negative battery terminal.
Is the diagnosis code No. B1625 set?
Go to Step 3.
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 3. Connector check: SRS-ECU, lap pre-tensioner.
(1) Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.
(2) After disconnecting the SRS-ECU connector, connect it again.
 
(3) After disconnecting the lap pre-tensioner harness side connector, connect the connector again. For the lap pre-tensioner harness side connector disconnection, use the flat-tipped screwdriver to pull out the harness side connector locking button. After releasing the lock, disconnect the harness side connector.
(4) Connect the negative battery terminal.
(5) After erasing the diagnosis code memory, check the diagnosis code again.
(6) Disconnect the negative battery terminal.
Is the diagnosis code No. B1625 set?
Go to Step 4.
Replace the connector concerned.
 
STEP 4. Diagnosis check by dummy resistor connection.
(1) Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.
 
(2) Use the flat-tipped screwdriver to pull out the locking button of harness side connector. After releasing the lock, disconnect the lap pre-tensioner harness side connector.
 
(3) Connect special tool dummy resistor (MB991865) to special tool resistor harness (MB991884).
(4) Connect resistor harness to the lap pre-tensioner harness side connector.
(5) Connect the negative battery terminal.
(6) After erasing the diagnosis code memory, check the diagnosis code again.
(7) Disconnect the negative battery terminal.
Is the diagnosis code No. B1625 set?
Go to Step 5.
Replace the seat belt with pre-tensioner (Refer to ).
 
STEP 5. Resistance measurement at the SRS-ECU connector.
(1) Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.
(2) Disconnect the SRS-ECU connector.
 
(3)
dangerTo release the SRS-ECU connector short spring in the following operations, disconnect this lap pre-tensioner connector, and keep the squib circuit shorted.
Use the flat-tipped screwdriver to pull out the locking button of harness side connector. After releasing the lock, disconnect the lap pre-tensioner harness side connector.
 
(4)
cautionThe short spring may not be released due to the insufficient insertion. Therefore, insert the insulator for 4 mm or more.
Insert an insulator (width: 3 mm, thickness: 0.5 mm) such as cable tie between the PA2-, PA2+, and then release the short spring.
(5) Take the measurements below at the SRS-ECU harness side connector.
  • Continuity between PA2-, PA2+ line
OK: No continuity
Is the check result normal?
Go to Step 6.
Repair the wiring harness PA2-, PA2+ line between the SRS-ECU connector and the lap pre-tensioner connector.
 
STEP 6. Check whether the diagnosis code is set again.
Is the diagnosis code No. B1625 set?
Replace SRS-ECU (Refer to ).
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).