Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and the long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the Air Fuel Ratio (A/F) sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if it is lean.
factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
If both the short-term and long-term fuel trims are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
When air fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on LEAN side (2 trip detection logic)
  1. Air induction system
  2. Injector blockage
  3. Mass Air Flow (MAF) meter
  4. Engine Coolant Temperature (ECT) sensor
  5. Fuel pressure
  6. Gas leakage in exhaust system
  7. Open or short in heated oxygen sensor (bank 1, 2 sensor 2)
  8. Heated oxygen sensor (bank 1, 2 sensor 1)
  9. Heated oxygen sensor heater (bank 1, 2 sensor 1)
  10. EFI relay
  11. PCV piping
  12. ECM
P0172
P0175
When air fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on RICH side (2 trip detection logic)
  1. Injector leak or blockage
  2. MAF meter
  3. ECT sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leakage in exhaust system
  7. Open or short in heated oxygen sensor (bank 1, 2 sensor 1) circuit
  8. Heated oxygen sensor (bank 1, 2 sensor 1)
  9. ECM

HINT:
  1. When DTC P0171 or P0174 is recorded, the actual air fuel ratio is on the LEAN side. When DTC P0172 or P0175 is recorded, the actual air fuel ratio is on the RICH side.
  2. If the vehicle runs out of fuel, the air fuel ratio is LEAN and DTC P0171 or P0174 may be recorded. The MIL is then illuminated.
  3. If the total of the short-term fuel trim value and long-term fuel trim value is within the malfunction threshold (and ECT is more than 75°C (167°F)), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection amounts that deviate from the ECM's estimated fuel amount will cause a change in the long-term fuel trim compensation value. Long-term fuel trim value is adjusted when persistent deviations in the short-term fuel trim's value are present. Also, the smoothed fuel trim learning value is adjusted when deviations from the ECM's simulated fuel injection value are present. The smoothed fuel trim learning value is the combination of smoothed short-term fuel trim (fuel feedback compensation value) and smoothed long-term fuel trim (learning value of the air fuel ratio). When the smoothed fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and sets a DTC.
Example:
The average fuel trim learning value is more than +35 % or less than -35 %, the ECM interprets this as a fuel system malfunction.

A121607E01


MONITOR STRATEGY


Related DTCs
P0171: Fuel trim Lean (bank 1)
P0172: Fuel trim Rich (bank 1)
P0174: Fuel trim Lean (bank 2)
P0175: Fuel trim Rich (bank 2)
Required Sensors/Components (Main)
Oxygen sensor, A/F sensor
Required Sensors/Components (Related)
Engine coolant temperature sensor, Mass Air Flow meter, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever these DTCs are not present
P0010, P0020 (OCV Bank 1, 2)
P0011 (VVT System 1 - Advance)
P0012 (VVT System 1 - Retard)
P0021 (VVT System 2 - Advance)
P0022 (VVT System 2 - Retard)
P0031, P0032, P0051, P0052 (A/F sensor heater - Sensor 1)
P0100 - P0103 (MAF meter)
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0335 (CKP sensor)
P0500 (VSS)
P2440 (AIR control valve stuck open)
P2441 (AIR control valve stuck close)
P2444 (AIP stuck ON)
P2445 (AIP stuck OFF)
Battery voltage
11 V or more
Fuel system status
Closed loop
Either of following conditions is met
Condition (a) or (b)
(a) Engine RPM
Less than 1,000 rpm
(b) Intake air amount per revolution
0.26 g/rev. or more
Catalyst monitor
Not executed

TYPICAL MALFUNCTION THRESHOLDS


Fuel trim: 
EVAP purge-cut
Executing
Either of following conditions is met
Condition (a) or (b)
(a) Average between short-term fuel trim and long-term fuel trim
+35 % or more (varies with ECT)
(b) Average between short-term fuel trim and long-term fuel trim
-35 % or less (varies with ECT)

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the A/F CONTROL function provided in the ACTIVE TEST. The A/F CONTROL function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the A/F CONTROL operation using an intelligent tester.
  1. Connect the intelligent tester to the DLC3 with CAN VIM.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine at engine speed of 2,500 rpm for approximately 90 seconds.
  4. On the tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
  5. Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection volume by 25 %.
  2. Each sensor reacts in accordance with increases in the fuel injection volume.


Standard: 
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1
(A/F)
+25 %
Rich
Less than 3.0
AFS B1S1 or AFS B2S1
(A/F)
-12.5 %
Lean
More than 3.35
O2S B1S2 or O2S B2S2
(HO2)
+25 %
Rich
More than 0.55
O2S B1S2 or O2S B2S2
(HO2)
-12.5 %
Lean
Less than 0.4

NOTICE:
The Air Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
Injection Volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
-
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
More than 0.55 V
Less than 0.4 V
A104057
2
Injection Volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
Output Voltage
Almost
no reaction
A103185
Output Voltage
More than 0.55 V
Less than 0.4 V
A104057
3
Injection Volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
Almost
no reaction
A103185
4
Injection volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
  1. Fuel injector
  2. Fuel pressure
  3. Gas leakage from exhaust system
    (Air fuel ratio extremely lean or rich)
Output Voltage
Almost
no reaction
A103185
Output Voltage
Almost
no reaction
A103185
  1. Following the A/F CONTROL procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL / USER DATA / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2. Then press the YES button and ENTER button, followed by the F4 button.

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  2. A low A/F sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174, P0175)
  1. Connect the intelligent tester to the CAN VIM. Then connect the CAN VIM to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0171, P0172, P0174 or P0175
    A
    P0171, P0172, P0174 or P0175 and other DTCs
    B

    HINT:
    If any DTCs other than P0171, P0172, P0174 and P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.CHECK CONNECTION OF VENTILATION HOSE

OK:
Ventilation hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE VENTILATION HOSE
OK


3.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK :
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (A/F CONTROL)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Start the engine and turn the tester ON.

  1. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.

  1. On the tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.

  1. Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)

  1. Monitor the outputs of A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection volume by 25 %.
    2. Each sensor reacts in accordance with increases in the fuel injection volume.


    Standard: 
    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS B1S1 or AFS B2S1
    (A/F)
    +25 %
    Rich
    Less than 3.0
    AFS B1S1 or AFS B2S1
    (A/F)
    -12.5 %
    Lean
    More than 3.35
    O2S B1S2 or O2S B2S2
    (HO2)
    +25 %
    Rich
    More than 0.55
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5 %
    Lean
    Less than 0.4

    Result:

    Status
    AFS B1S1
    or
    AFS B2S1
    Status
    O2S B1S2
    or
    O2S B2S2
    A/F Condition and
    A/F Sensor Condition
    Misfires
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    C
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. Ventilation valve and hose
    2. Ventilation hose connections
    3. Injector blockage
    4. Gas leakage from exhaust system
    5. Air induction system
    6. Fuel pressure
    7. Mass Air Flow (MAF) meter
    8. Engine Coolant Temperature (ECT) sensor
    A
    Rich
    Rich
    Actual air fuel ratio lean
    -
    1. Injector leakage or blockage
    2. Gas leakage from exhaust system
    3. Injection system
    4. Fuel pressure
    5. MAF meter
    6. ECT sensor
    A
    Lean
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    B

    Lean: During A/F CONTROL, the A/F sensor output voltage (AFS) is consistently more than 3.35 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.
    Rich: During A/F CONTROL, the AFS is consistently less than 3.0 V, and the O2S is consistently more than 0.55 V.
    Lean/Rich: During A/F CONTROL of the ACTIVE TEST, the output voltage of the heated oxygen sensor alternates correctly.



B
Go to step 11

C
Go to step 15
A


5.READ VALUE OF INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.

  1. Read the COOLANT TEMP value when the engine is cold and warmed-up.

    Standard:
    ECT when the engine is cold: Same as ambient temperature
    ECT when the engine is warmed-up: 75 to 95°C (167 to 203°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


6.READ VALUE OF INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / MAF and COOLANT TEMP.

  1. Allow the engine to idle until the COOLANT TEMP reaches 75°C (167°F) or more.

  1. Read the MAF with the engine in an idling condition and at an engine speed of 2, 500 rpm.

    Standard:
    MAF at idle rpm: 1.4 g/sec. and 2.3 g/sec. (shift lever is in N position and A/C is OFF)
    MAF at 2,500 rpm: 5.4 g/sec. and 7.9 g/sec. (shift lever is in N position and A/C is OFF)



NG
REPLACE MASS AIR FLOW METER
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAKAGE

OK:
No gas leakage.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FOR SPARK AND IGNITION
  1. Check for spark and ignition (Click here).

HINT:
If the spark plugs or ignition system malfunction, engine misfire may occur. The misfire counter can be read with the intelligent tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / CYL #1 (to CYL #8).



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
  1. Inspect the fuel injector (Click here).

HINT:
If the injectors are malfunctioning, engine misfire may occur. The misfire counter can be read with the intelligent tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / CYL #1 (to CYL #8).



NG
REPLACE FUEL INJECTOR
OK


11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A085152E60
  1. Disconnect the A12 or A13 Air Fuel Ratio (A/F) sensor connectors.

  1. Measure the resistance of the A/F sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    HT (1) - +B (2)
    1.8 to 3.4 kΩ at 20°C (68°F)
    HT (1) - AF- (4)
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR
OK


12.INSPECT A/F RELAY


    B016200E02
  1. Remove the A/F relay from the engine room relay block.

  1. Measure the resistance of the A/F relay.

    Standard resistance:
    Terminal Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE A/F RELAY
OK


13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)


    A121613E02
  1. Disconnect the A12 or A13 A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the +B terminal of the A/F sensor connector and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +B (2) - Body ground
    9 to 14 V

  1. Turn the ignition switch to OFF.

  1. Disconnect the E5 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester connections
    Specified Conditions
    HT (A12-1) - HA1A (E5-2)
    HT (A13-1) - HA2A (E5-1)
    Below 1 Ω
    AF+ (A12-3) - A1A+ (E5-22)
    AF+ (A13-3) - A2A+ (E5-23)
    Below 1 Ω
    AF- (A12-4) - A1A- (E5-30)
    AF- (A13-4) - A2A- (E5-31)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester connections
    Specified Conditions
    HT (A12-1) or HA1A (E5-2) - Body ground
    HT (A13-1) or HA2A (E5-1) - Body ground
    10 kΩ or higher
    AF+ (A12-3) or A1A+ (E5-22) - Body ground
    AF+ (A13-3) or A2A+ (E5-23) - Body ground
    10 kΩ or higher
    AF- (A12-4) or A1A- (E5-30) - Body ground
    AF- (A13-4) or A2A- (E5-31) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.



  1. Reconnect the A/F sensor connector.


    A118002E03



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR

NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN

A115372E40

  1. Connect the intelligent tester to the DLC3 with CAN VIM [A].

  1. Turn the ignition switch ON and turn the tester ON [B].

  1. Clear DTCs (Click here) [C].

  1. Switch the ECM from normal mode to check mode using the tester (Click here) [D].

  1. Start the engine and warm it up with all the accessories switched OFF [E].

  1. Drive the vehicle at between 38 and 75 mph (60 and 120 km/h) and at an engine speed of between 1,400 rpm and 3,200 rpm for 3 to 5 minutes [F].

    HINT:
    If the system is still malfunctioning, the MIL will be illuminated during step [F].

    NOTICE:
    If the conditions in this test are not strictly followed, no malfunction will be detected.


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
  1. On the intelligent tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P0171, P0172, P0174 or P0175
    B



B
Go to step 5
A

END