DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| Condition (a) of DTC P0120, P0122, P0123, P0220, P0222 or P0223 continues for 2 seconds (Open or short in the throttle position sensor circuit) | ||
| P0120 | Detection conditions for DTCs P0122 and P0123 are not satisfied but condition (a) is satisfied: (a) VTA1 is "0.2 V or less" or VTA1 is "4.535 V or more" |
|
| P0122 | (a) VTA1 is 0.2 V or less |
|
| P0123 | (a) VTA1 is 4.535 V or more |
|
| P0220 | Detection conditions for DTCs P0222 and P0223 are not satisfied but condition (a) is satisfied (a) VTA2 is "1.75 V or less" or VTA2 is "4.8 V or more" |
|
| P0222 | (a) VTA2 is 1.75 V or less |
|
| P0223 | (a) VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V |
|
| P2135 | Condition (a) continues for 0.5 second or more, or condition (b) continues for 0.4 second or more: (a) Difference between VTA1 and VTA2 is 0.02 V or less (b) VTA1 is 0.2 V or less and VTA2 is 1.75 V or less |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| THROTTLE POS | 10 to 24% | 64 to 96% |
| THROTTLE POS #2 | 2.1 to 3.1 V | 4.5 to 5.5 V |
| Related DTCs | P0120: Throttle position sensor 1 range check (fluttering) P0122: Throttle position sensor 1 range check (low voltage) P0123: Throttle position sensor 1 range check (high voltage) P0220: Throttle position sensor 2 range check (fluctuating) P0222: Throttle position sensor 2 range check (low voltage) P0223: Throttle position sensor 2 range check (high voltage) P2135: Throttle position sensor range check (correlation) |
| Required sensors/components (Main) | Throttle position sensor |
| Required sensors/components (Related) | - |
| Frequency of operation | Continuous |
| Duration | Accelerator pedal ON: 2 seconds Accelerator pedal OFF: 10 seconds P2135: 0.5 seconds or 0.4 seconds |
| MIL operation | Immediate |
| Sequence of operation | None |
| Monitor will run whenever these DTCs are not present | None |
| Throttle control motor power | ON |
| Ignition switch | ON |
| VTA1 voltage | 0.2 V or less, or 4.535 V or more |
| VTA1 voltage | 0.2 V or less |
| VTA1 voltage | 4.535 V or more |
| VTA1 voltage | 1.75 V or less or 4.8 V or more |
| VTA2 voltage | 1.75 V or less |
| VTA2 voltage when the VTA1 is 0.2 to 2.02 V | 4.8 V or more |
| Either of the following condition A or B is met | - |
| Condition A | - |
| Difference between VTA and VTA2 voltage | 0.02 V or less |
| Condition B | - |
| VTA1 voltage | 0.2 V or less |
| VTA2 voltage | 1.75 V or less |
| VTA1 voltage | 0.6 to 3.96 V |
| VTA2 voltage | 2.25 to 5.0 V |

| 1.READ VALUE OF INTELLIGENT TESTER (THROTTLE POS, THROTTLE POS #2) |
![]() |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ETCS / THROTTLE POS and THROTTLE POS #2 .
Read the value.
| Throttle position expressed as percentage and voltage | Trouble Area | Proceed to | |||
| Accelerator pedal depressed | Accelerator pedal released | ||||
| THROTTLE POS (VTA1) | THROTTLE POS #2 (VTA2) | THROTTLE POS (VTA1) | THROTTLE POS #2 (VTA2) | ||
| 0 % | 0 to 0.2 V | 0 % | 0 to 0.2 V | VC circuit open | A |
| 100 % | 4.5 to 5.5 V | 100 % | 4.5 to 5.5 V | E2 circuit open | |
| 0 % or 100 % | 2.1 to 3.1 V (fail-safe) | 0 % or 100 % | 2.1 to 3.1 V (fail-safe) | VTA1 circuit open or ground short | |
| 10 to 24 % (fail-safe) | 0 to 0.2 or 4.5 to 5.5 V | 10 to 24 % (Fail safe) | 0 to 0.2 or 4.5 to 5.5 V | VTA2 circuit open or ground short | |
| 10 to 24 % | 2.1 to 3.1 V | 64 to 96 % (Does not fail safe) | 4.5 to 5.5 V (Does not fail safe) | TP sensor circuit is normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the T2 throttle body connector.
Disconnect the E4 ECM connector.
Measure the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| VC (T2-5) - VC (E4-23) | Below 1 Ω |
| VTA1 (T2-6) - VTA1 (E4-20) | |
| VTA2 (T2-4) - VTA2 (E4-19) | |
| E2 (T2-3) - E2 (E4-28) | |
| VC (T2-5) or VC (E4-23) - Body ground | 10 kΩ or higher |
| VTA1 (T2-6) or VTA1 (E4-20) - Body ground | |
| VTA2 (T2-4) or VTA2 (E4-19) - Body ground |
Reconnect the throttle body connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK ECM (VC VOLTAGE) |
![]() |
Disconnect the T2 throttle body connector.
Turn the ignition switch ON.
Measure the voltage of the ECM.
| Tester Connection | Specified Condition |
| VC (E4-23) - E2 (E4-28) | 4.5 to 5.5 V |
Reconnect the throttle body connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY |
Replace the throttle body (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS ARE OUTPUT AGAIN) |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Clear the DTC (Click here).
Start the engine and allow the engine to idle for 15 seconds or more.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read the DTC.
| Display (DTC Output) | Proceed to |
| P0120, P0122, P0123, P0220, P0222, P0223 or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||