Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DTC    P2197    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)

DTC    P2198    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. Although the DTC titles refer to the "oxygen sensor", these DTCs relate to the Air Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

The A/F sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

HINT:
*: Value changes inside the ECM. Since the A/F sensor is the current output element, the current is converted to a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.


A107164E07


DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 2 seconds or more
(2 trip detection logic):
(a) Air Fuel Ratio (A/F) sensor voltage more than 3.8 V
(b) Heated Oxygen (HO2) sensor voltage 0.15 V or more
  1. Open or short in Air Fuel Ratio (A/F) sensor (bank 1, 2 sensor 1) circuit
  2. Air Fuel Ratio (A/F) sensor (bank 1, 2 sensor 1)
  3. Air Fuel Ratio (A/F) sensor (bank 1, 2 sensor 1) heater
  4. A/F relay
  5. A/F sensor heater and relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Fuel injector
  9. ECM
P2195
P2197
While fuel-cut operation performed (during vehicle deceleration), air fuel ratio (A/F) sensor current 3.6 mA or more for 3 seconds (2 trip detection logic)
  1. A/F sensor
  2. ECM
P2196
P2198
Conditions (a) and (b) continue for 2 seconds or more
(2 trip detection logic):
(a) A/F sensor voltage less than 2.8 V
(b) HO2 sensor voltage less than 0.85 V
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor (bank 1, 2 sensor 1) heater
  4. A/F relay
  5. A/F sensor heater and relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Fuel injector
  9. ECM
P2196
P2198
While fuel-cut operation performed (during vehicle deceleration), air fuel ratio (A/F) sensor current 1.4 mA for 3 seconds (2 trip detection logic)
  1. A/F sensor
  2. ECM

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes No. 1 cylinder.
  4. Bank 2 refers to the bank that includes No. 2 cylinder.
  5. When any of these DTCs are set, check the A/F sensor output voltage by entering the following menus on the intelligent tester: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / AFS B1S1.
  6. Short-term fuel trim values can also be read using the intelligent tester.
  7. The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor output voltage cannot be confirmed without using the intelligent tester.
  8. If an A/F sensor malfunction is detected, the ECM sets a DTC.


MONITOR DESCRIPTION

  1. Sensor voltage detection monitor
    Under the air fuel ratio feedback control, if the A/F sensor output voltage indicates rich or lean for a certain period of time, the ECM determines that is a malfunction in the A/F sensor. The ECM illuminates the MIL and sets a DTC.
    Example:
    If the A/F sensor voltage output is less than 2.8 V (very rich condition) for 10 seconds, despite the HO2 sensor output voltage being less than 0.6 V, the ECM sets DTC P2196. Alternatively, if the A/F sensor output voltage is more than 3.8 V (very lean condition) for 15 seconds, despite the HO2 sensor output voltage being 0.15 V or more, DTC P2195 is set.
  2. Sensor current detection monitor:
    A rich air-fuel mixture causes a low air-fuel ratio sensor current, and a lean air fuel mixture causes a high air-fuel ratio sensor current. Therefore, the sensor output becomes high during acceleration, and the sensor becomes low during deceleration.
    The ECM monitors the air-fuel ratio sensor current during fuel-cut and detects unusual current value. If the cumulative time sensor output exceeds 3 seconds, the ECM interprets a malfunction in the air-fuel ratio sensor and sets a DTC.

A133737E01


MONITOR STRATEGY


Related DTCs
P2195: A/F sensor (Bank 1) signal stuck lean
P2196: A/F sensor (Bank 1) signal stuck rich
P2197: A/F sensor (Bank 2) signal stuck lean
P2198: A/F sensor (Bank 2) signal stuck rich
Required Sensors/Components
A/F sensor
Frequency of Operation
Continuous
Duration
15 seconds: A/F sensor signal stuck lean/rich
3 seconds: A/F sensor current (high/low side)
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever these DTCs are not present
P0031, P0032, P0051, P0052 (A/F sensor heater - Sensor 1)
P0037, P0038, P0057, P0058 (O2 sensor heater - Sensor 2)
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0136, P0156 (O2 Sensor - Sensor 2)
P0171, P0172 (Fuel system)
P0300 - P0308 (Misfire)
P0335 (CKP sensor)
P0455, P0456 (EVAP system)
P0500 (VSS)
P2440 (AIR control valve stuck open)
P2441 (AIR control valve stuck close)
P2444 (AIP stuck ON)
P2445 (AIP stuck OFF)

Sensor voltage detection monitor (Lean side malfunction P2195, P2197): 
Time while all of following conditions met
2 seconds or more
Rear HO2 sensor voltage
0.15 V or more
Time after engine start
30 seconds or more
A/F sensor status
Activated
Fuel system status
closed-loop
Engine
Running

Sensor voltage detection monitor (Rich side malfunction P2196, P2198): 
Time while all of following conditions met
2 seconds or more
Rear HO2 sensor voltage
Below 0.6 V
Time after engine start
30 seconds or more
A/F sensor status
Activated
Fuel system status
closed-loop
Engine
Running

Sensor current detection monitor P2195, P2196, P2197 and P2198 
Battery voltage
11 V or more
Atmospheric pressure
570 mmHg or higher
Air-fuel ratio sensor status
Activated
ECT
75°C (167°F) or more
Continuous time of fuel cut
3 to 10 seconds

TYPICAL MALFUNCTION THRESHOLDS


Sensor voltage detection monitor (Lean side malfunction P2195, P2197): 
A/F sensor voltage
More than 3.8 V

Sensor voltage detection monitor (Rich side malfunction P2196, P2198): 
A/F sensor voltage
Less than 2.8 V

Sensor current detection monitor (High side malfunction P2195, P2197): 
Air-fuel ratio sensor current during fuel cut
3.6 mA or more

Sensor current detection monitor (Rich side malfunction P2196, P2198): 
Air-fuel ratio sensor current during fuel cut
Less than 1.4 mA

MONITOR RESULT

Detailed information on Checking Monitor Status (Click here).
The test value and test limit information are described as shown in the following table. Check the monitor result and test values after performing the monitor driving pattern (refer to "Confirmation Monitor").
  1. MID (Monitor Identification Data) is assigned to each emissions-related component.
  2. TID (Test Identification Data) is assigned to each test value.
  3. Scaling is used to calculate the test value indicated on generic OBD II scan tools.

    A/F sensor bank 1 sensor 1 
    MID
    TID
    Scaling
    Description of Test Value
    Minimum Test Limit
    Maximum Test Limit
    $01
    $91
    Multiply by 0.003906 (mA)
    A/F current
    Minimum test limit
    Maximum test limit

    A/F sensor bank 2 sensor 1 
    MID
    TID
    Scaling
    Description of Test Value
    Minimum Test Limit
    Maximum Test Limit
    $01
    $91
    Multiply by 0.003906 (mA)
    A/F current
    Minimum test limit
    Maximum test limit

WIRING DIAGRAM


A130714E01


CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the following diagnostic troubleshooting inspection procedure when using the intelligent tester.

A107162E20


A107163E13

  1. Connect the intelligent tester to the DLC3 with CAN VIM [A].
  2. Turn the ignition switch ON [B].
  3. Turn the tester ON [C].
  4. Clear DTCs (Click here) [D].
  5. Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher [E].
  6. On the intelligent tester, enter the following menus to check the fuel-cut status: DIAGNOSIS / ENHANCED OBD II / DATA LIST / USER DATA / FC IDLE [F].
  7. Drive the vehicle at between 38 mph (60 km/h) and 75 mph (120 km/h) for at least 10 minutes [G].
  8. Change the transmission to 2nd gear [H].
  9. Drive the vehicle at proper vehicle speed to perform fuel-cut operation [I].

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal fully released.
    2. Engine speed is 2,500 rpm or more (fuel injection returns at 1,000 rpm).

  10. Accelerate the vehicle to 40 rpm (64 km/h) or more by depressing the accelerator pedal for at least 10 seconds [J].
  11. Soon after performing step [J] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [K].
  12. Allow the vehicle to decelerate until the vehicle speed declines to less than 6 mph (10 km/h) [L].
  13. Repeat steps from [I] through [L] above at least 3 times in one driving cycle [M].

    HINT:
    Completion of all A/F sensor monitors is required to change the value in TEST RESULT.

    CAUTION:
    Strictly observe posted speed limits, traffic laws, and road conditions when performing these drive patterns.


INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the A/F CONTROL function provided in the ACTIVE TEST. The A/F CONTROL function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the A/F CONTROL operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3 with CAN VIM.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. On the intelligent tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
  5. Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection volume by 25 %.
    2. Each sensor reacts in accordance with increases in the fuel injection volume.


    Standard: 
    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS B1S1 or AFS B2S1
    (A/F)
    +25 %
    Rich
    Less than 3.0
    AFS B1S1 or AFS B2S1
    (A/F)
    -12.5 %
    Lean
    More than 3.35
    O2S B1S2 or O2S B2S2
    (HO2)
    +25 %
    Rich
    More than 0.55
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5 %
    Lean
    Less than 0.4

    NOTICE:
    The Air Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


    Case
    A/F Sensor (Sensor 1)
    Output Voltage
    HO2 Sensor (Sensor 2)
    Output Voltage
    Main Suspected Trouble Areas
    1
    Injection Volume
    +25 %
    -12.5 %
    A103184
    Injection Volume
    +25 %
    -12.5 %
    A103184
    -
    Output Voltage
    More than 3.35 V
    Less than 3.0 V
    A112626
    Output Voltage
    More than 0.55 V
    Less than 0.4 V
    A104057
    2
    Injection Volume
    +25 %
    -12.5 %
    A103184
    Injection Volume
    +25 %
    -12.5 %
    A103184
    1. A/F sensor
    2. A/F sensor heater
    3. A/F sensor circuit
    Output Voltage
    Almost
    no reaction
    A103185
    Output Voltage
    More than 0.55 V
    Less than 0.4 V
    A104057
    3
    Injection Volume
    +25 %
    -12.5 %
    A103184
    Injection Volume
    +25 %
    -12.5 %
    A103184
    1. HO2 sensor
    2. HO2 sensor heater
    3. HO2 sensor circuit
    Output Voltage
    More than 3.35 V
    Less than 3.0 V
    A112626
    Output Voltage
    Almost
    no reaction
    A103185
    4
    Injection volume
    +25 %
    -12.5 %
    A103184
    Injection Volume
    +25 %
    -12.5 %
    A103184
    1. Fuel injector
    2. Fuel pressure
    3. Gas leakage from exhaust system
      (Air fuel ratio extremely lean or rich)
    Output Voltage
    Almost
    no reaction
    A103185
    Output Voltage
    Almost
    no reaction
    A103185
  1. Following the A/F CONTROL procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus on the tester: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL / USER DATA / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2. Then press the YES button and ENTER button, followed by the F4 button.

    HINT:
    1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
    2. A low A/F sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
    3. A high A/F sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, 2197 OR P2198)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON.

  1. Turn the tester ON

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197, or P2198
    A
    P2195, P2196, P2197, or P2198 and other DTCs
    B

    HINT:
    If any DTCs other than P2195, P2196, P2197 or P2198 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.READ VALUE OF INTELLIGENT TESTER (TEST VALUE OF A/F SENSOR)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Allow the vehicle to drive in accordance with the drive pattern described in the CONFIRMATION DRIVING PATTERN.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / MONITOR INFO / MONITOR STATUS.

  1. Check the the status of O2S MON is COMPL.
    If the status is still INCMPL, drive the vehicle according to the driving pattern again.

HINT:
  1. AVAIL indicates that the component has not been monitored yet.
  2. COMPL indicates that the component is functioning normally.
  3. INCMPL indicates that the component is malfunctioning.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / MONITOR INFO / TEST RESULT / RANGE B1S1; then press the ENTER button.

  1. Check the test value of the A/F sensor output current during fuel-cut.

    Result:

    Test Value
    Proceed to
    Within normal range (1.4 mA or more, and less than 3.6 mA)
    A
    Outside normal range (Less than 1.4 mA, or 3.6 mA or more)
    B



B
Go to step 20
A


3.READ VALUE OF INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Start the engine.

  1. Turn the tester ON.

  1. Warm up the Air Fuel Ratio (A/F) sensor at an engine speed of 2,500 rpm for 90 seconds.

  1. On the tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / SNAPSHOT / MANUAL SNAPSHOT / USER DATA / AFS B1S1 or AFS B2S1 and ENGINE SPD.

  1. Check the A/F sensor voltage three times, when the engine is in each of the following conditions:
    Operation Steps 
    Step
    Condition
    (1)
    While idling (check for at least 30 seconds)
    (2)
    At an engine speed of approximately 2,500 rpm (without any sudden changes in engine speed)
    (3)
    Raise the engine speed to 4,000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed.

    Standard voltage:

    Condition
    A/F Sensor Voltage Variation
    Reference
    (1) and (2)
    Changes at approximately 0.66 V
    Between 0.62 and 0.7 V
    (3)
    Increases to 0.76 V or more
    This occurs during engine deceleration
    (when fuel-cut performed)

    HINT:

    1. For more information, see the diagrams below.


      A107161E13

    2. If the output voltage of the A/F sensor remains at approximately 0.66 V (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have an open circuit (this will also happen if the A/F sensor heater has an open circuit).
    3. If the output voltage of the A/F sensor remains at either approximately 0.76 V or more, or 0.56 V or less (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have a short circuit.
    4. The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the A/F sensor output voltage.
    5. The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 10 mph (16 km/h) to allow the ECM to learn the closed throttle valve position.
    6. When the vehicle is driven:
      The output voltage of the A/F sensor may be below 0.56 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The A/F sensor is functioning normally.
    7. The A/F sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the A/F sensor or ECM will show a constant voltage result.



NG
Go to step 10
OK


4.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read DTCs using the intelligent tester.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

    Result:

    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197, or P2198
    A
    No output
    B



B
Go to step 9
A


6.REPLACE AIR FUEL RATIO SENSOR

NEXT


7.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read DTCs using the intelligent tester.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197, or P2198
    B



B
REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN
A


9.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST


NO
CHECK FOR INTERMITTENT PROBLEMS
YES

DTC CAUSED BY RUNNING OUT OF FUEL 

10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A085152E60
  1. Disconnect the A12 or A13 A/F sensor connector.

  1. Measure the resistance of the A/F sensor connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    HT (1) - +B (2)
    1.8 Ω to 3.4 Ω at 20°C (68°F)
    HT (1) - AF- (4)
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


11.INSPECT A/F RELAY


    B016200E02
  1. Remove the A/F relay from the engine room relay block.

  1. Measure the resistance of the A/F relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the A/F relay.



NG
REPLACE A/F RELAY
OK


12.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)


    A121613E02
  1. Disconnect the A12 or A13 A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the +B terminal of the A/F sensor connector and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +B (2) - Body ground
    Between 9 V and 14 V

  1. Turn the ignition switch to OFF.

  1. Disconnect the E5 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    HT (A12-1) - HA1A (E5-2)
    HT (A13-1) - HA2A (E5-1)
    Below 1 Ω
    AF+ (A12-3) - A1A+ (E5-22)
    AF+ (A13-3) - A2A+ (E5-23)
    Below 1 Ω
    AF- (A12-4) - A1A- (E5-30)
    AF- (A13-4) - A2A- (E5-31)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    HT (A12-1) or HA1A (E5-2) - Body ground
    HT (A13-1) or HA2A (E5-1) - Body ground
    10 kΩ or higher
    AF+ (A12-3) or A1A+ (E5-22) - Body ground
    AF+ (A13-3) or A2A+ (E5-23) - Body ground
    10 kΩ or higher
    AF- (A12-4) or A1A- (E5-30) - Body ground
    AF- (A13-4) or A2A- (E5-31) - Body ground
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



  1. Reconnect the ECM connector.


    A118002E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage.

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


14.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


15.INSPECT FUEL INJECTOR
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).



NG
REPLACE FUEL INJECTOR
OK


16.REPLACE AIR FUEL RATIO SENSOR

NEXT


17.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read DTCs using the intelligent tester.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198
    B



B
REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN
A


19.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST


NO
CHECK FOR INTERMITTENT PROBLEMS
YES

DTC CAUSED BY RUNNING OUT OF FUEL 

20.REPLACE AIR FUEL RATIO SENSOR

NEXT


21.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


22.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Read DTCs using the intelligent tester.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198 (A/F sensor pending DTCs)
    B



B
REPLACE ECM
A

END