Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON / OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag assembly condition (activated/not activated) by the passenger airbag ON/OFF indicator.
The table below shows the normal indication condition of the passenger airbag ON/OFF indicator and the front passenger seat condition.

Front passenger seat condition
ON Indicator
OFF Indicator
Adult is seated.
ON
OFF
Child is seated.
OFF
ON
Vacant
OFF
OFF
Occupant classification system failure
OFF
ON

INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to the ON position, and check the SRS warning light condition.

    HINT:
    If this trouble occurs, the SRS warning light is off. If it is on, a DTC is output. Troubleshoot for the output DTC.

    OK:
    The SRS warning light does not come on.



NG
Go to step 9
OK


2.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the ignition switch to the ON position.

  1. Check if the passenger airbag ON/OFF indicator correctly indicates the front passenger seat condition.

    OK:

    Front passenger seat condition
    ON Indicator
    OFF Indicator
    Adult is seated.
    ON
    OFF
    Child is seated.
    OFF
    ON
    Vacant
    OFF
    OFF
    Occupant classification system failure
    OFF
    ON



OK
END
NG


3.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch to the LOCK position.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform "Zero point calibration" (Click here).

    OK:
    "COMPLETE" is displayed.



NG
Go to step 5
OK


4.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 5
OK

END 

5.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the ignition switch to the LOCK position.

  1. Loosen the 4 installation bolts of the front seat assembly RH.

  1. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Torque:
37 N*m{ 380 kgf*cm , 27 ft.*lbf }



NG
Go to step 8
OK


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform "Zero point calibration" (Click here).

    OK:
    "COMPLETE" is displayed.



NG
Go to step 8
OK


7.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 8
OK


8.CHECK CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Check the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

    OK:
    The connectors are connected.

  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

  1. Check the connectors are not damaged or deformed.

    OK:
    The connectors are properly normal.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


9.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Turn the ignition switch to the LOCK position.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC is not output.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


10.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


11.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform "Zero point calibration" (Click here).

    OK:
    "COMPLETE" is displayed.


NEXT


12.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END