Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2444    Secondary Air Injection System Pump Stuck On Bank1

DTC    P2445    Secondary Air Injection System Pump Stuck Off Bank1

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P2444
Air pump stuck ON.
The secondary air pressure is more than 5 kPa (38 mmHg) despite the ECM ordering the air pump to turn off.
(2 trip detection logic)
  1. Short in air pump circuit
  2. Air injection control driver (AID)
  3. Pressure sensor
  4. Open or short in pressure sensor circuit
  5. ECM
P2445
Air pump stuck OFF or air injection volume is insufficient.
The amount of air flow is below the criteria.
(The secondary air pressure is less than specified value despite the ECM ordering the air pump turn ON.)
(2 trip detection logic)
  1. Air pump fuse
  2. Vacuum hose
  3. Air pump assembly
  4. Air injection control driver (AID)
  5. Open in air pump circuit
  6. Air injection system piping
  7. Pressure sensor
  8. Open or short in pressure sensor circuit
  9. ECM

MONITOR DESCRIPTION

P2444:
The ECM observes the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system. The sensor measures the pressure in the secondary air passage and sends a signal to the ECM.
If the pressure level from the sensor exceeds a certain level despite the ECM turning off the air pump, the ECM interprets this as a fault in the secondary air injection system and sets a DTC.
P2445:
The ECM calculates the amount of air flow within the secondary air system based on the output values of the pressure sensor and mass air flow meter.
The ECM determines whether the amount of air flow is normal or not according to the calculated value. When the amount of air flow is below the criteria, the ECM stores the DTC and illuminates the MIL.

MONITOR STRATEGY


Related DTCs
(Case 1) P2444 Air pump stuck ON
(Case 2) P2445 Air pump stuck OFF
(Case 3) P2445 Air insufficient
(Case 4) P2445 Air pressure sensor stuck
Required sensors/Components
Air pressure sensor, AIR pump
Frequency of operation
Continuous
Duration
Within 60 seconds
MIL operation
2 driving cycles
Sequence operation
None

TYPICAL ENABLING CONDITIONS


All: 
This monitor runs whenever these DTCs are not present
P0010 - P0022 (VVT system)
P0031 - P0052 (A/F sensor heater)
P0100 - P0103 (MAF sensor)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Closed loop)
P0171, P0172 (Fuel trim)
P0300 - P0308 (Misfire)
P0327 - P0333 (Knock sensor)
P0335 (CKP sensor)
P0340 - P0346 (VVT sensor)
P0351 - P0358 (Ignitor)
P0455, P0456 (EVAP system)
P0450, P0453 (EVAP press sensor)
P0500 (VSS)
P2196, P2198 (A/F sensor - rationality)
P2430 - P2433 (AIR pressure sensor)
P2A00, P2A03 (A/F sensor - slow response)

Conditions for case 1, 2 and 3: 
Atmospheric pressure
45 kPa (420 mmHg) or more
Battery voltage
11.5 V or higher
AIR monitor runs in accordance with the monitor sequence 1 to 5
-
Monitor Sequence 1
AIR
In operation
AIR pump
ON
AIR valve
ON
Either of following conditions is met
Condition 1 or 2
1. Both of the following conditions are met
Condition (a) and (b)
(a) AIR valve bank 1
ON
(b) AIR valve bank 2
OFF
2. Both of the following conditions are met
Condition (c) and (d)
(c) AIR valve bank 1
OFF
(d) AIR valve bank 2
ON
Monitor Sequence 2
Idle
ON
AIR valve (electric type)
ON
AIR valve (vacuum type) bank 1
ON
AIR valve (vacuum type) bank 2
ON
Monitor Sequence 3
Engine RPM
Less than 3,750 rpm
AIR pump
ON
AIR valve (electric type)
ON
AIR valve bank 1 (vacuum type)
ON
AIR valve bank 2 (vacuum type)
ON
Monitor Sequence 4
Runs when AIR pressure did not change at monitor sequence 2
Engine RPM
Less than 3,750 rpm
AIR
Not operating
AIR pump
ON
AIR valve (electric type)
ON
Either of following conditions is met
Condition 1 or 2
1. Both of the following conditions are met
Condition (a) and (b)
(a) AIR valve bank 1
ON
(b) AIR valve bank 2
OFF
2. Both of the following conditions are met
Condition (c) and (d)
(c) AIR valve bank 1
OFF
(d) AIR valve bank 2
ON
Monitor Sequence 5
Engine RPM
Less than 3,750 rpm
AIR
Not operating
AIR pump
OFF
AIR valve (electric type)
OFF
AIR VSV bank 1 (vacuum type)
OFF
AIR VSV bank 2 (vacuum type)
OFF
Monitor Sequence 6
Engine RPM
Less than 3,750 rpm
AIR status
OFF
AIR pump
OFF
AIR valve (electric type)
ON
AIR VSV bank 1 (vacuum type)
OFF
AIR VSV bank 2 (vacuum type)
OFF

Conditions for case 4: 
ECT at engine start
Less than 5°C (41°F)
IAT at engine start
-15°C (5°F) or more
Time that ECT is 80°C (176°F) or higher
10 to 60 minutes
Cumulative intake air amount
172 g/sec. or more
Monitor sequence 3 (during AIR: ON)
Completed
One of the following conditions is met:
Condition (a), (b) or (c)
(a) Vehicle speed
49.7 mph (80 km/h) or more
(b) Engine RPM
0 rpm or more
(c) Throttle position
0 deg. or more
AIR valve
OFF
AIR VSV bank 1
OFF
AIR VSV bank 2
OFF
AIR pressure sensor malfunction (open circuit, out of range)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


Case 1: 
AIR pressure monitor sequence 6
5 kPa (37.5 mmHg) or more

Case 2: 
AIR pressure monitor sequence 3
Less than 1 kPa (7.5 mmHg)

Case 3: 
AIR amount
100 L/min. or less

Case 4: 
AIR pressure change
5 kPa (37.5 mmHg) or more

MONITOR RESULT

Refer to Checking Monitor Status (Click here).
The test value and test limit information are described as shown in the following table. Check the monitor result and test values after performing the monitor drive pattern (refer to "Confirmation Monitor").
  1. MID (Monitor Identification Data) is assigned to each emissions-related component.
  2. TID (Test Identification Data) is assigned to each test value.
  3. Scaling is used to calculate the test value indicated on generic OBD II scan tools.

    Secondary air injection (AIR) system 
    MID
    TID
    Scaling
    Description of Test Value
    Minimum Test Limit
    Maximum Test Limit
    $71
    $E1
    Multiply by 0.01 (g/s)
    Test value of AIR amount insufficient
    Minimum test limit
    Maximum test limit
    $71
    $E2
    Multiply by 0.01 (kPa)
    Test value of AIR pump stuck ON
    Minimum test limit
    Maximum test limit
    $71
    $E3
    Multiply by 0.01 (kPa)
    Test value of AIR pump stuck OFF
    Minimum test limit
    Maximum test limit
    $71
    $E4
    Multiply by 0.01 (kPa)
    Test value of AIR control valve ON
    Minimum test limit
    Maximum test limit
    $71
    $E5
    Multiply by 0.01 (kPa)
    Test value of AIR control valve OFF
    Minimum test limit
    Maximum test limit
    $71
    $E6
    Multiply by 0.01 (kPa)
    Test value of AIR pressure change for AIR valve
    Minimum test limit
    Maximum test limit
    $71
    $E7
    Multiply by 0.01 (kPa)
    Test value of AIR pressure change for AIR VSV bank 1
    Minimum test limit
    Maximum test limit
    $71
    $E8
    Multiply by 0.01 (kPa)
    Test value of AIR pressure change for AIR VSV bank 2
    Minimum test limit
    Maximum test limit
    $71
    $E9
    Multiply by 0.01 (kPa)
    Test value of AIR pressure pulsation for AIR VSV when AIR pressure is low
    Minimum test limit
    Maximum test limit

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444 AND P2445)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and push the intelligent tester main switch ON.

  1. Enter the following menus: DIAGNOSIS/ENHANCED OBD II/DTC INFO/CURRENT CODES.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2445
    A
    P2444
    B
    P2444 and P2445
    "P2444 and P2445" and other DTCs
    C

    HINT:
    If any other codes besides P2444 or P2445 is output, perform the troubleshooting for those DTCs first.



B
Go to step 7

C
GO TO DTC CHART
A


2.CHECK AIR INJECTION SYSTEM PRESSURE


    A115721
  1. Start the engine and warm it up.

  1. Turn the ignition switch OFF.

  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and push the intelligent tester main switch ON.

  1. Start the engine.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / MANUAL OPERATION / OPERATION 1 and 2.

    HINT:
    OPERATION 1: AP: OFF, EASV: CLOSE, ASV1: CLOSE, ASV2: CLOSE
    OPERATION 2: AP: ON, EASV: OPEN, ASV1: OPEN, ASV2: OPEN

  1. Check that the PRESSURE on the intelligent tester.

    NOTICE:
    This test only allows technicians to operate the AI system for 5 seconds. Furthermore, the test can be performed 4 times a trip. If the test is repeated, intervals of at least 30 seconds are required between tests.
    While the AI system operation using the intelligent tester is prohibited, the tester displays the prohibition (WAIT or ERROR). If ERROR (AI STATUS NG) is displayed on the tester, stop the engine for 10 minutes and then try again.

    Standard pressure:
    Tester operation
    Pressure
    Operation 1
    Less than 2.5 kPa
    Operation 2
    5 to 8 kPa or more



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Start the engine and warm it up.

  1. Turn the ignition switch OFF.

  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Perform ACTIVE TEST to operate the air injection system.
    Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / AUTOMATIC OPERATION

  1. After operating the secondary air injection system, confirm the pending codes for the secondary air injection system by entering the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.

  1. Read DTC and check DTC.

    OK:
    DTC P2444 or P2445 for the secondary air injection system is not output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS 

4.CHECK VACUUM HOSES


    G032743E01
  1. Remove the intake manifold .

  1. Check the vacuum hose connection between the pressure sensor and air switching valve.

    OK:
    The vacuum hose is securely connected.

  1. Inspect the vacuum hose for blockage and damage.

    OK:
    The vacuum hose has no blockage and damage.



NG
REPAIR OR REPLACE VACUUM HOSES
OK


5.READ VALUE OF INTELLIGENT TESTER (AIR VOLTAGE)


    G032742E01
  1. Remove the intake manifold .

  1. Connect the pressure gauge to the pressure sensor as shown in the illustration.

  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and push the intelligent tester main switch ON (Do not start engine).

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / AIR PMP PRS.

  1. Check that the pressure displayed on the intelligent tester fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

    OK:
    Pressure fluctuates in response to the pressure applied with pressure gauge.



NG
REPLACE PRESSURE SENSOR
OK


6.CHECK PIPING AND HOSES (CONNECTION OF ALL AIR INJECTION SYSTEM)


    G032737E01
  1. Remove the intake manifold .

  1. Check that all the pipes and hoses between the air pump and air switching valve are securely connected.

    OK:
    All air injection pipes and hoses are securely connected.

  1. Check all pipes and hoses for blockages and damage.

    OK:
    All air injection pipes and hoses have no blockages and damage.



NG
REPAIR OR REPLACE AIR INJECTION SYSTEM PIPING AND HOSES
OK


7.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)


    A115722E02
  1. Remove the intake manifold .

  1. Disconnect the A44 Air Injection Control Driver (AID) connectors.

  1. Turn the ignition switch ON.

  1. Measure the voltage between terminals A44-5 (+B) and A43-1 (BATT) of the AID and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (A44-5) - Body ground
    10 V or more
    BATT (A43-1) - Body ground

  1. Measure the resistance between the terminal A44-1 (E) of the AID and body ground.

    Standard resistance:
    Tester Connection
    Specified Condition
    E (A44-1) - Body ground
    Below 1 Ω

  1. Reconnect the AID connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT ECM (AIRP AND AIRV VOLTAGE)


    E118245E25
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. When the air pump and air switching valve are operated using the intelligent tester, measure voltage between terminal E8-25 (AIRP) and E8-4 (AIRV) of the AID connector and body ground.

    Standard voltage:
    Tester Connection
    Air pump operation
    Specified Condition
    AIRP (E8-25) - Body ground
    ON
    10 V or more
    AIRP (E8-25) - Body ground
    OFF
    3.5 to 7.7 V*

    Standard voltage:
    Tester Connection
    Air switching valve (ASV) operation (EASV)
    Specified Condition
    AIRV (E8-4) - Body ground
    OPEN
    10 V or more
    AIRV (E8-4) - Body ground
    CLOSE
    3.5 to 7.7 V*

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / MANUAL OPERATION / OPERATION 1 and 2.

    HINT:
    OPERATION 1: AP: OFF, EASV: CLOSE, ASV1: CLOSE, ASV2: CLOSE
    OPERATION 2: AP: ON, EASV: OPEN, ASV1: OPEN, ASV2: OPEN

    NOTICE:
    This test only allows technicians to operate the AI system for 5 seconds. Furthermore, the test can be performed 4 times a trip. If the test is repeated, intervals of at least 30 seconds are required between tests.
    While the AI system operation using the intelligent tester is prohibited, the tester displays the prohibition (WAIT or ERROR). If ERROR (AI STATUS NG) is displayed on the tester, stop the engine for 10 minutes and then try again.

    HINT:
    *: 35 to 55 % of the +B voltage.



NG
REPLACE ECM
OK


9.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - BODY GROUND)


    A115723E02
  1. Disconnect the A44 air injection driver connector.

  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. When the air pump and air switching valve are operated using the intelligent tester, measure the voltage between terminals A44-3 (SIV) and A44-4 (SIP) of the air injection driver connector and body ground.

    Standard voltage:
    Tester Connection
    Air pump operation
    Specified Condition
    SIP (A44-4) - Body ground
    ON
    10 V or more
    SIP (A44-4) - Body ground
    OFF
    3.5 to 7.7 V*

    Standard voltage:
    Tester Connection
    ASV operation (EASV)
    Specified Condition
    SIV (A44-3) - Body ground
    OPEN
    10 V or more
    SIV (A44-3) - Body ground
    CLOSE
    3.5 to 7.7 V*

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / MANUAL OPERATION / OPERATION 1 and 2.

    HINT:
    OPERATION 1: AP: OFF, EASV: CLOSE, ASV1 : CLOSE, ASV2: CLOSE
    OPERATION 2: AP: ON, EASV: OPEN, ASV1: OPEN, ASV2: OPEN

    NOTICE:
    This test only allows technicians to operate the AI system for 5 seconds. Furthermore, the test can be performed 4 times a trip. If the test is repeated, intervals of at least 30 seconds are required between tests.
    While the AI system operation using the intelligent tester is prohibited, the tester displays the prohibition (WAIT or ERROR). If the ERROR (AI STATUS NG) is displayed on the tester, stop the engine for 10 minutes and then try again.

    *: 35 to 55 % of the +B voltage.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT AIR PUMP (OPERATION)


    A115725E01
  1. Remove the hose between EASV and ASV.

  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / AIR INJ CHECK / MANUAL / OPERATION / OPERATION 2.

  1. When the air pump is operated, check that air comes out from the air pump.

    HINT:
    OPERATION 2: AP: ON, EASV: CLOSE, ASV1: CLOSE, ASV2: CLOSE

    NOTICE:
    1. This test only allows technicians to operate the AI system for 5 seconds. Furthermore, the test can be performed 4 times a trip. If the test is repeated, intervals of at least 30 seconds are required between tests.
      While the AI system operation using the intelligent tester is prohibited, the tester displays the prohibition (WAIT or ERROR). If ERROR (AI STATUS NG) is displayed on the tester, stop the engine for 10 minutes and then try again.
    2. When performing the AIR INJ CHECK operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned ON or the engine running.
    3. Turn the ignition switch OFF when the AIR INJ CHECK operation finishes.

    OK:
    Air comes out from the air pump



NG
REPLACE AIR PUMP
OK

CHECK WHETHER DTC OUTPUT NOT RECURS