Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1246/46    Master Cylinder Pressure Sensor Malfunction

for Preparation Click here


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the master cylinder solenoid.

C124773E02


DTC No.
DTC Detection Condition
Trouble Area
C1246/46
When any of the following conditions is detected:
1. Both of the following conditions continue for at least 30 seconds.
  1. Vehicle speed is more than 4 mph (7 km/h).
  2. PMC terminal voltage does not change by more than 0.005 V once it exceeds 0.86 V.
2. PMC terminal receives interference at least 7 times within 5 seconds.
3. Both of the following conditions continue for at least 1.2 seconds.
  1. Stop light switch is OFF.
  2. PMC terminal voltage is more than 0.86 V or less than 0.3 V.
4. Both of the following conditions continue for at least 1.2 seconds.
  1. IG1 terminal voltage is between 9.5 and 17 V.
  2. VCM terminal voltage is not between 4.4 and 5.6 V.
5. Both of the following conditions continue for at least 1.2 seconds.
  1. VCM terminal voltage is between 4.4 and 5.6 V.
  2. PMC terminal voltage is not between 0.14 and 4.85 V.
  1. Master cylinder pressure sensor
  2. Master cylinder pressure sensor circuit
  3. Stop light switch circuit
  4. Master cylinder solenoid

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.READ VALUE OF INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select "DATA LIST" mode on the intelligent tester.

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    MAS CYL PRESS 1
    Master cylinder pressure sensor 1 reading / Min.: 0 V, Max.: 5 V
    1. When brake pedal is released: 0.3 to 0.9 V
    2. When stop light is turned on: 0.3 to 0.9 V
    Reading increases when brake pedal is depressed

  1. Check that the master cylinder pressure value of the master cylinder pressure sensor displayed on the intelligent tester changes when depressing the brake pedal.

    Result:

    Condition
    Proceed to
    Master cylinder pressure sensor value does not change
    A
    Master cylinder pressure sensor value changes but it is not normal
    B
    Master cylinder pressure sensor value becomes normal
    C



A
REPLACE MASTER CYLINDER SOLENOID

C
Go to step 4
B


2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Check the brake pedal height.

  1. Check the stop light switch installation.

    OK:
    The brake pedal and stop light switch are normal.



NG
ADJUST BRAKE PEDAL AND/OR STOP LIGHT SWITCH
OK


3.INSPECT SKID CONTROL ECU (STP TERMINAL)


    C121700E80
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S28-7 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    8 to 14 V
    S28-7 (STP) - Body ground
    Stop light switch OFF (Brake pedal released
    Below 1.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


4.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID