Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1202/52    Brake Fluid Level Low / Open Circuit in Brake Fluid Level Warning Switch Circuit

DTC    C1202/58    Brake Fluid Level Low / Open Circuit in Brake Fluid Level Warning Switch Circuit

for Preparation Click here


DESCRIPTION

The brake fluid level warning switch sends the appropriate signal to the skid control ECU when the brake fluid level drops.

DTC No.
DTC Detection Condition
Trouble Area
C1202/52
C1202/58
When either of the following conditions is detected:
  1. With ECU terminal IG1 voltage at 9.5 V to 17.2 V, an open in the brake fluid level warning switch circuit continues for 2 seconds or more.
  2. Fluid level of the reservoir tank is LOW for 4 seconds or 40 seconds after the ignition switch is turned ON, of for 7 seconds during pump motor operation.
  1. Brake fluid level
  2. Brake fluid level warning switch
  3. Brake fluid level warning switch circuit

HINT:
If the code (C1202/52) is output, the following situations will occur:
  1. The VSC TRAC and BRAKE warning lights, and the VSC OFF indicator light will come on.
  2. Control of all systems other than ABS and EBD is canceled.
If the code (C1202/58) is output, the following situations will occur:
  1. The ABS, VSC TRAC, and BRAKE warning lights, and the SLIP and VSC OFF indicator lights will come on.
  2. Control of all systems other than EBD is canceled.


WIRING DIAGRAM


C132913E01


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

HINT:
When C1241/41 is output together with C1202/52 or C1202/58, inspect and repair the trouble areas indicated by C1241/41 first.

1.CHECK BRAKE FLUID LEVEL
  1. Turn the ignition switch off.

  1. Depress the brake pedal 20 times or more (until the pedal reaction feels light and pedal stroke becomes longer).

  1. Check the amount of fluid in the brake reservoir.

    HINT:
    When the ignition switch is turned to the ON position, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).

    NOTICE:
    Do not move the wheels with the ignition switch off.

    OK:
    Brake fluid level is proper.



NG
CHECK AND REPAIR BRAKE FLUID LEAKAGE
OK


2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    F052341E04
  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    1. A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.
    2. The warning switch is switched ON/OFF at +- 5mm from the MIN level.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B14-1 - B14-2
    Float UP (Switch OFF)
    1.9 to 2.1 kΩ
    B14-1 - B14-2
    Float DOWN (Switch ON)
    Below 1 Ω

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH - SKID CONTROL ECU)


    I045330E03
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-41 (LBL) - B14-2
    Below 1 Ω
    S28-41 (LBL) - Body ground
    10 kΩ or higher
    B14-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTCs are detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID