Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1380/64    Stop Light Control Relay Malfunction

for Preparation Click here


DESCRIPTION

Upon receiving the DAC or HAC operating signal from the skid control ECU, the relay contact turns on and the stop light comes on.

DTC No.
DTC Detection Condition
Trouble Area
C1380/64
  1. When the voltage at the IG1 terminal is between 10 V and 14 V and the stop light driving output (STPO) is on, a signal has not been input to the STP terminal for 5 seconds or more.
  2. When the voltage at the IG1 terminal is between 10 V and 14 V and the stop light driving output (STPO) is off, the input signal at the STP is different from the input signal at the STP2 for 5 seconds or more.
  1. Stop light operation relay
  2. Stop light operation relay circuit

WIRING DIAGRAM


C132920E05


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.

    OK:
    Stop light switch function is normal.

    HINT:
    Check the stop light bulb as it may have burnt out.



NG
Go to step 9
OK


2.INSPECT SKID CONTROL ECU (STP TERMINAL)


    C121700E86
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S28-7 (STP) - Body ground
    Stop light switch ON
    (Brake pedal depressed)
    8 to 14 V
    S28-7 (STP) - Body ground
    Stop light switch OFF
    (Brake pedal released)
    Below 1.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


3.INSPECT SKID CONTROL ECU (STP2 TERMINAL)


    C121700E87
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-7 (STP) - S28-45 (STP2)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK


4.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (STOP LIGHT OPERATION RELAY)
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select "ACTIVE TEST" mode on the intelligent tester.

    Item
    Vehicle Condition / Test Details
    Diagnostic Note
    STOP LIGHT RELAY
    Turns stop light operation relay ON / OFF
    Observe rear combination light
    (Does not come on for 5 sec. or more)

  1. Check that "ON" and "OFF" of the stop light can be shown on the rear combination light by the intelligent tester.

OK:
The stop light turns on or off in accordance with the intelligent tester.



OK
Go to step 8
NG


5.INSPECT STOP LIGHT OPERATION RELAY (POWER SOURCE TERMINAL)


    I045958E01
  1. Remove the stop light operation relay.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    1 - Body ground
    8 to 14 V
    5 - Body ground
    8 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6.INSPECT STOP LIGHT OPERATION RELAY


    F052359E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    10 kΩ or higher
    (When battery positive voltage is applied to terminal 1 and battery negative voltage to terminal 2.)
    3 - 5
    Below 1 Ω
    (When battery positive voltage is applied to terminal 1 and battery negative voltage to terminal 2.)



NG
REPLACE STOP LIGHT OPERATION RELAY
OK


7.INSPECT SKID CONTROL ECU (STPO TERMINAL)


    C121700E88
  1. Instal the stop light operation relay.

  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    S28-16 (STPO) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)
OK


8.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID 

9.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE TERMINAL)


    C124801E03
  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S12-2 Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


10.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C124796E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S12-1 - S12-2
    Switch pin free
    Below 1 Ω
    S12-1 - S12-2
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - STOP LIGHT OPERATION RELAY)


    I046068E02
  1. Remove the stop light operation relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S12-1 - 4
    Below 1 Ω
    S12-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT STOP LIGHT OPERATION RELAY


    F052359E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω



NG
REPLACE STOP LIGHT OPERATION RELAY
OK


13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - STOP LIGHT OPERATION RELAY)


    I046069E03
  1. Disconnect the rear combination light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    R14-1 - 3
    Below 1 Ω
    R14-1 - Body ground
    10 kΩ or higher
    R14-6 - Body ground
    Below 1 Ω

    RH:
    Tester Connection
    Specified Condition
    R15-1 - 3
    Below 1 Ω
    R15-1 - Body ground
    10 kΩ or higher
    R15-6 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

END